| #pragma once |
| |
| // Special keycodes |
| #define KEY_HOME 0xE0 |
| #define KEY_END 0xE1 |
| #define KEY_UP 0xE2 |
| #define KEY_DN 0xE3 |
| #define KEY_LF 0xE4 |
| #define KEY_RT 0xE5 |
| #define KEY_PGUP 0xE6 |
| #define KEY_PGDN 0xE7 |
| #define KEY_INS 0xE8 |
| #define KEY_DEL 0xE9 |
| |
| |
| /* This is i8042reg.h + kbdreg.h from NetBSD. */ |
| |
| #define KBSTATP 0x64 /* kbd controller status port(I) */ |
| #define KBS_DIB 0x01 /* kbd data in buffer */ |
| #define KBS_IBF 0x02 /* kbd input buffer low */ |
| #define KBS_WARM 0x04 /* kbd input buffer low */ |
| #define KBS_OCMD 0x08 /* kbd output buffer has command */ |
| #define KBS_NOSEC 0x10 /* kbd security lock not engaged */ |
| #define KBS_TERR 0x20 /* kbd transmission error */ |
| #define KBS_RERR 0x40 /* kbd receive error */ |
| #define KBS_PERR 0x80 /* kbd parity error */ |
| |
| #define KBCMDP 0x64 /* kbd controller port(O) */ |
| #define KBC_RAMREAD 0x20 /* read from RAM */ |
| #define KBC_RAMWRITE 0x60 /* write to RAM */ |
| #define KBC_AUXDISABLE 0xa7 /* disable auxiliary port */ |
| #define KBC_AUXENABLE 0xa8 /* enable auxiliary port */ |
| #define KBC_AUXTEST 0xa9 /* test auxiliary port */ |
| #define KBC_KBDECHO 0xd2 /* echo to keyboard port */ |
| #define KBC_AUXECHO 0xd3 /* echo to auxiliary port */ |
| #define KBC_AUXWRITE 0xd4 /* write to auxiliary port */ |
| #define KBC_SELFTEST 0xaa /* start self-test */ |
| #define KBC_KBDTEST 0xab /* test keyboard port */ |
| #define KBC_KBDDISABLE 0xad /* disable keyboard port */ |
| #define KBC_KBDENABLE 0xae /* enable keyboard port */ |
| #define KBC_PULSE0 0xfe /* pulse output bit 0 */ |
| #define KBC_PULSE1 0xfd /* pulse output bit 1 */ |
| #define KBC_PULSE2 0xfb /* pulse output bit 2 */ |
| #define KBC_PULSE3 0xf7 /* pulse output bit 3 */ |
| |
| #define KBDATAP 0x60 /* kbd data port(I) */ |
| #define KBOUTP 0x60 /* kbd data port(O) */ |
| |
| #define K_RDCMDBYTE 0x20 |
| #define K_LDCMDBYTE 0x60 |
| |
| #define KC8_TRANS 0x40 /* convert to old scan codes */ |
| #define KC8_MDISABLE 0x20 /* disable mouse */ |
| #define KC8_KDISABLE 0x10 /* disable keyboard */ |
| #define KC8_IGNSEC 0x08 /* ignore security lock */ |
| #define KC8_CPU 0x04 /* exit from protected mode reset */ |
| #define KC8_MENABLE 0x02 /* enable mouse interrupt */ |
| #define KC8_KENABLE 0x01 /* enable keyboard interrupt */ |
| #define CMDBYTE (KC8_TRANS|KC8_CPU|KC8_MENABLE|KC8_KENABLE) |
| |
| /* keyboard commands */ |
| #define KBC_RESET 0xFF /* reset the keyboard */ |
| #define KBC_RESEND 0xFE /* request the keyboard resend the last byte */ |
| #define KBC_SETDEFAULT 0xF6 /* resets keyboard to its power-on defaults */ |
| #define KBC_DISABLE 0xF5 /* as per KBC_SETDEFAULT, but also disable key scanning */ |
| #define KBC_ENABLE 0xF4 /* enable key scanning */ |
| #define KBC_TYPEMATIC 0xF3 /* set typematic rate and delay */ |
| #define KBC_SETTABLE 0xF0 /* set scancode translation table */ |
| #define KBC_MODEIND 0xED /* set mode indicators(i.e. LEDs) */ |
| #define KBC_ECHO 0xEE /* request an echo from the keyboard */ |
| |
| /* keyboard responses */ |
| #define KBR_EXTENDED 0xE0 /* extended key sequence */ |
| #define KBR_RESEND 0xFE /* needs resend of command */ |
| #define KBR_ACK 0xFA /* received a valid command */ |
| #define KBR_OVERRUN 0x00 /* flooded */ |
| #define KBR_FAILURE 0xFD /* diagnosic failure */ |
| #define KBR_BREAK 0xF0 /* break code prefix - sent on key release */ |
| #define KBR_RSTDONE 0xAA /* reset complete */ |
| #define KBR_ECHO 0xEE /* echo response */ |
