| /******************************************************************************* |
| |
| Intel PRO/1000 Linux driver |
| Copyright(c) 1999 - 2008 Intel Corporation. |
| |
| This program is free software; you can redistribute it and/or modify it |
| under the terms and conditions of the GNU General Public License, |
| version 2, as published by the Free Software Foundation. |
| |
| This program is distributed in the hope it will be useful, but WITHOUT |
| ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or |
| FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for |
| more details. |
| |
| You should have received a copy of the GNU General Public License along with |
| this program; if not, write to the Free Software Foundation, Inc., |
| 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA. |
| |
| The full GNU General Public License is included in this distribution in |
| the file called "COPYING". |
| |
| Contact Information: |
| Linux NICS <linux.nics@intel.com> |
| e1000-devel Mailing List <e1000-devel@lists.sourceforge.net> |
| Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497 |
| |
| *******************************************************************************/ |
| |
| #ifndef _E1000_DEFINES_H_ |
| #define _E1000_DEFINES_H_ |
| |
| /* Number of Transmit and Receive Descriptors must be a multiple of 8 */ |
| #define REQ_TX_DESCRIPTOR_MULTIPLE 8 |
| #define REQ_RX_DESCRIPTOR_MULTIPLE 8 |
| |
| /* Definitions for power management and wakeup registers */ |
| /* Wake Up Control */ |
| #define E1000_WUC_APME 0x00000001 /* APM Enable */ |
| #define E1000_WUC_PME_EN 0x00000002 /* PME Enable */ |
| #define E1000_WUC_PME_STATUS 0x00000004 /* PME Status */ |
| #define E1000_WUC_APMPME 0x00000008 /* Assert PME on APM Wakeup */ |
| #define E1000_WUC_LSCWE 0x00000010 /* Link Status wake up enable */ |
| #define E1000_WUC_LSCWO 0x00000020 /* Link Status wake up override */ |
| #define E1000_WUC_SPM 0x80000000 /* Enable SPM */ |
| #define E1000_WUC_PHY_WAKE 0x00000100 /* if PHY supports wakeup */ |
| |
| /* Wake Up Filter Control */ |
| #define E1000_WUFC_LNKC 0x00000001 /* Link Status Change Wakeup Enable */ |
| #define E1000_WUFC_MAG 0x00000002 /* Magic Packet Wakeup Enable */ |
| #define E1000_WUFC_EX 0x00000004 /* Directed Exact Wakeup Enable */ |
| #define E1000_WUFC_MC 0x00000008 /* Directed Multicast Wakeup Enable */ |
| #define E1000_WUFC_BC 0x00000010 /* Broadcast Wakeup Enable */ |
| #define E1000_WUFC_ARP 0x00000020 /* ARP Request Packet Wakeup Enable */ |
| #define E1000_WUFC_IPV4 0x00000040 /* Directed IPv4 Packet Wakeup Enable */ |
| #define E1000_WUFC_IPV6 0x00000080 /* Directed IPv6 Packet Wakeup Enable */ |
| #define E1000_WUFC_IGNORE_TCO 0x00008000 /* Ignore WakeOn TCO packets */ |
| #define E1000_WUFC_FLX0 0x00010000 /* Flexible Filter 0 Enable */ |
| #define E1000_WUFC_FLX1 0x00020000 /* Flexible Filter 1 Enable */ |
| #define E1000_WUFC_FLX2 0x00040000 /* Flexible Filter 2 Enable */ |
| #define E1000_WUFC_FLX3 0x00080000 /* Flexible Filter 3 Enable */ |
| #define E1000_WUFC_ALL_FILTERS 0x000F00FF /* Mask for all wakeup filters */ |
| #define E1000_WUFC_FLX_OFFSET 16 /* Offset to the Flexible Filters bits */ |
| #define E1000_WUFC_FLX_FILTERS 0x000F0000 /*Mask for the 4 flexible filters */ |
| |
| /* Wake Up Status */ |
| #define E1000_WUS_LNKC E1000_WUFC_LNKC |
| #define E1000_WUS_MAG E1000_WUFC_MAG |
| #define E1000_WUS_EX E1000_WUFC_EX |
| #define E1000_WUS_MC E1000_WUFC_MC |
| #define E1000_WUS_BC E1000_WUFC_BC |
| #define E1000_WUS_ARP E1000_WUFC_ARP |
| #define E1000_WUS_IPV4 E1000_WUFC_IPV4 |
| #define E1000_WUS_IPV6 E1000_WUFC_IPV6 |
| #define E1000_WUS_FLX0 E1000_WUFC_FLX0 |
| #define E1000_WUS_FLX1 E1000_WUFC_FLX1 |
| #define E1000_WUS_FLX2 E1000_WUFC_FLX2 |
| #define E1000_WUS_FLX3 E1000_WUFC_FLX3 |
| #define E1000_WUS_FLX_FILTERS E1000_WUFC_FLX_FILTERS |
| |
| /* Wake Up Packet Length */ |
| #define E1000_WUPL_LENGTH_MASK 0x0FFF /* Only the lower 12 bits are valid */ |
| |
| /* Four Flexible Filters are supported */ |
| #define E1000_FLEXIBLE_FILTER_COUNT_MAX 4 |
| |
| /* Each Flexible Filter is at most 128 (0x80) bytes in length */ |
| #define E1000_FLEXIBLE_FILTER_SIZE_MAX 128 |
| |
| #define E1000_FFLT_SIZE E1000_FLEXIBLE_FILTER_COUNT_MAX |
| #define E1000_FFMT_SIZE E1000_FLEXIBLE_FILTER_SIZE_MAX |
| #define E1000_FFVT_SIZE E1000_FLEXIBLE_FILTER_SIZE_MAX |
| |
| /* Extended Device Control */ |
| #define E1000_CTRL_EXT_GPI0_EN 0x00000001 /* Maps SDP4 to GPI0 */ |
| #define E1000_CTRL_EXT_GPI1_EN 0x00000002 /* Maps SDP5 to GPI1 */ |
| #define E1000_CTRL_EXT_PHYINT_EN E1000_CTRL_EXT_GPI1_EN |
| #define E1000_CTRL_EXT_GPI2_EN 0x00000004 /* Maps SDP6 to GPI2 */ |
| #define E1000_CTRL_EXT_GPI3_EN 0x00000008 /* Maps SDP7 to GPI3 */ |
| /* Reserved (bits 4,5) in >= 82575 */ |
| #define E1000_CTRL_EXT_SDP4_DATA 0x00000010 /* Value of SW Definable Pin 4 */ |
| #define E1000_CTRL_EXT_SDP5_DATA 0x00000020 /* Value of SW Definable Pin 5 */ |
| #define E1000_CTRL_EXT_PHY_INT E1000_CTRL_EXT_SDP5_DATA |
| #define E1000_CTRL_EXT_SDP6_DATA 0x00000040 /* Value of SW Definable Pin 6 */ |
| #define E1000_CTRL_EXT_SDP7_DATA 0x00000080 /* Value of SW Definable Pin 7 */ |
| /* SDP 4/5 (bits 8,9) are reserved in >= 82575 */ |
| #define E1000_CTRL_EXT_SDP4_DIR 0x00000100 /* Direction of SDP4 0=in 1=out */ |
| #define E1000_CTRL_EXT_SDP5_DIR 0x00000200 /* Direction of SDP5 0=in 1=out */ |
| #define E1000_CTRL_EXT_SDP6_DIR 0x00000400 /* Direction of SDP6 0=in 1=out */ |
| #define E1000_CTRL_EXT_SDP7_DIR 0x00000800 /* Direction of SDP7 0=in 1=out */ |
| #define E1000_CTRL_EXT_ASDCHK 0x00001000 /* Initiate an ASD sequence */ |
| #define E1000_CTRL_EXT_EE_RST 0x00002000 /* Reinitialize from EEPROM */ |
| #define E1000_CTRL_EXT_IPS 0x00004000 /* Invert Power State */ |
| #define E1000_CTRL_EXT_SPD_BYPS 0x00008000 /* Speed Select Bypass */ |
| #define E1000_CTRL_EXT_RO_DIS 0x00020000 /* Relaxed Ordering disable */ |
| #define E1000_CTRL_EXT_DMA_DYN_CLK_EN 0x00080000 /* DMA Dynamic Clock Gating */ |
| #define E1000_CTRL_EXT_LINK_MODE_MASK 0x00C00000 |
| #define E1000_CTRL_EXT_LINK_MODE_GMII 0x00000000 |
| #define E1000_CTRL_EXT_LINK_MODE_TBI 0x00C00000 |
| #define E1000_CTRL_EXT_LINK_MODE_KMRN 0x00000000 |
| #define E1000_CTRL_EXT_LINK_MODE_PCIE_SERDES 0x00C00000 |
| #define E1000_CTRL_EXT_LINK_MODE_PCIX_SERDES 0x00800000 |
| #define E1000_CTRL_EXT_LINK_MODE_SGMII 0x00800000 |
| #define E1000_CTRL_EXT_EIAME 0x01000000 |
| #define E1000_CTRL_EXT_IRCA 0x00000001 |
| #define E1000_CTRL_EXT_WR_WMARK_MASK 0x03000000 |
| #define E1000_CTRL_EXT_WR_WMARK_256 0x00000000 |
| #define E1000_CTRL_EXT_WR_WMARK_320 0x01000000 |
| #define E1000_CTRL_EXT_WR_WMARK_384 0x02000000 |
| #define E1000_CTRL_EXT_WR_WMARK_448 0x03000000 |
| #define E1000_CTRL_EXT_CANC 0x04000000 /* Int delay cancellation */ |
| #define E1000_CTRL_EXT_DRV_LOAD 0x10000000 /* Driver loaded bit for FW */ |
| /* IAME enable bit (27) was removed in >= 82575 */ |
| #define E1000_CTRL_EXT_IAME 0x08000000 /* Int acknowledge Auto-mask */ |
| #define E1000_CRTL_EXT_PB_PAREN 0x01000000 /* packet buffer parity error |
| * detection enabled */ |
| #define E1000_CTRL_EXT_DF_PAREN 0x02000000 /* descriptor FIFO parity |
| * error detection enable */ |
| #define E1000_CTRL_EXT_GHOST_PAREN 0x40000000 |
| #define E1000_CTRL_EXT_PBA_CLR 0x80000000 /* PBA Clear */ |
| #define E1000_I2CCMD_REG_ADDR_SHIFT 16 |
| #define E1000_I2CCMD_REG_ADDR 0x00FF0000 |
| #define E1000_I2CCMD_PHY_ADDR_SHIFT 24 |
| #define E1000_I2CCMD_PHY_ADDR 0x07000000 |
| #define E1000_I2CCMD_OPCODE_READ 0x08000000 |
| #define E1000_I2CCMD_OPCODE_WRITE 0x00000000 |
| #define E1000_I2CCMD_RESET 0x10000000 |
| #define E1000_I2CCMD_READY 0x20000000 |
| #define E1000_I2CCMD_INTERRUPT_ENA 0x40000000 |
| #define E1000_I2CCMD_ERROR 0x80000000 |
| #define E1000_MAX_SGMII_PHY_REG_ADDR 255 |
| #define E1000_I2CCMD_PHY_TIMEOUT 200 |
| |
| /* Receive Descriptor bit definitions */ |
| #define E1000_RXD_STAT_DD 0x01 /* Descriptor Done */ |
| #define E1000_RXD_STAT_EOP 0x02 /* End of Packet */ |
| #define E1000_RXD_STAT_IXSM 0x04 /* Ignore checksum */ |
| #define E1000_RXD_STAT_VP 0x08 /* IEEE VLAN Packet */ |
| #define E1000_RXD_STAT_UDPCS 0x10 /* UDP xsum calculated */ |
| #define E1000_RXD_STAT_TCPCS 0x20 /* TCP xsum calculated */ |
| #define E1000_RXD_STAT_IPCS 0x40 /* IP xsum calculated */ |
| #define E1000_RXD_STAT_PIF 0x80 /* passed in-exact filter */ |
| #define E1000_RXD_STAT_CRCV 0x100 /* Speculative CRC Valid */ |
| #define E1000_RXD_STAT_IPIDV 0x200 /* IP identification valid */ |
| #define E1000_RXD_STAT_UDPV 0x400 /* Valid UDP checksum */ |
| #define E1000_RXD_STAT_DYNINT 0x800 /* Pkt caused INT via DYNINT */ |
| #define E1000_RXD_STAT_ACK 0x8000 /* ACK Packet indication */ |
| #define E1000_RXD_ERR_CE 0x01 /* CRC Error */ |
| #define E1000_RXD_ERR_SE 0x02 /* Symbol Error */ |
| #define E1000_RXD_ERR_SEQ 0x04 /* Sequence Error */ |
| #define E1000_RXD_ERR_CXE 0x10 /* Carrier Extension Error */ |
| #define E1000_RXD_ERR_TCPE 0x20 /* TCP/UDP Checksum Error */ |
| #define E1000_RXD_ERR_IPE 0x40 /* IP Checksum Error */ |
| #define E1000_RXD_ERR_RXE 0x80 /* Rx Data Error */ |
| #define E1000_RXD_SPC_VLAN_MASK 0x0FFF /* VLAN ID is in lower 12 bits */ |
| #define E1000_RXD_SPC_PRI_MASK 0xE000 /* Priority is in upper 3 bits */ |
| #define E1000_RXD_SPC_PRI_SHIFT 13 |
| #define E1000_RXD_SPC_CFI_MASK 0x1000 /* CFI is bit 12 */ |
| #define E1000_RXD_SPC_CFI_SHIFT 12 |
| |
| #define E1000_RXDEXT_STATERR_CE 0x01000000 |
| #define E1000_RXDEXT_STATERR_SE 0x02000000 |
| #define E1000_RXDEXT_STATERR_SEQ 0x04000000 |
| #define E1000_RXDEXT_STATERR_CXE 0x10000000 |
| #define E1000_RXDEXT_STATERR_TCPE 0x20000000 |
| #define E1000_RXDEXT_STATERR_IPE 0x40000000 |
| #define E1000_RXDEXT_STATERR_RXE 0x80000000 |
| |
| /* mask to determine if packets should be dropped due to frame errors */ |
| #define E1000_RXD_ERR_FRAME_ERR_MASK ( \ |
| E1000_RXD_ERR_CE | \ |
| E1000_RXD_ERR_SE | \ |
| E1000_RXD_ERR_SEQ | \ |
| E1000_RXD_ERR_CXE | \ |
| E1000_RXD_ERR_RXE) |
| |
| /* Same mask, but for extended and packet split descriptors */ |
| #define E1000_RXDEXT_ERR_FRAME_ERR_MASK ( \ |
| E1000_RXDEXT_STATERR_CE | \ |
| E1000_RXDEXT_STATERR_SE | \ |
| E1000_RXDEXT_STATERR_SEQ | \ |
| E1000_RXDEXT_STATERR_CXE | \ |
| E1000_RXDEXT_STATERR_RXE) |
| |
| #define E1000_MRQC_ENABLE_MASK 0x00000007 |
| #define E1000_MRQC_ENABLE_RSS_2Q 0x00000001 |
| #define E1000_MRQC_ENABLE_RSS_INT 0x00000004 |
| #define E1000_MRQC_RSS_FIELD_MASK 0xFFFF0000 |
| #define E1000_MRQC_RSS_FIELD_IPV4_TCP 0x00010000 |
| #define E1000_MRQC_RSS_FIELD_IPV4 0x00020000 |
| #define E1000_MRQC_RSS_FIELD_IPV6_TCP_EX 0x00040000 |
| #define E1000_MRQC_RSS_FIELD_IPV6_EX 0x00080000 |
| #define E1000_MRQC_RSS_FIELD_IPV6 0x00100000 |
| #define E1000_MRQC_RSS_FIELD_IPV6_TCP 0x00200000 |
| |
| #define E1000_RXDPS_HDRSTAT_HDRSP 0x00008000 |
| #define E1000_RXDPS_HDRSTAT_HDRLEN_MASK 0x000003FF |
| |
| /* Management Control */ |
| #define E1000_MANC_SMBUS_EN 0x00000001 /* SMBus Enabled - RO */ |
| #define E1000_MANC_ASF_EN 0x00000002 /* ASF Enabled - RO */ |
| #define E1000_MANC_R_ON_FORCE 0x00000004 /* Reset on Force TCO - RO */ |
| #define E1000_MANC_RMCP_EN 0x00000100 /* Enable RCMP 026Fh Filtering */ |
| #define E1000_MANC_0298_EN 0x00000200 /* Enable RCMP 0298h Filtering */ |
| #define E1000_MANC_IPV4_EN 0x00000400 /* Enable IPv4 */ |
| #define E1000_MANC_IPV6_EN 0x00000800 /* Enable IPv6 */ |
| #define E1000_MANC_SNAP_EN 0x00001000 /* Accept LLC/SNAP */ |
| #define E1000_MANC_ARP_EN 0x00002000 /* Enable ARP Request Filtering */ |
| /* Enable Neighbor Discovery Filtering */ |
| #define E1000_MANC_NEIGHBOR_EN 0x00004000 |
| #define E1000_MANC_ARP_RES_EN 0x00008000 /* Enable ARP response Filtering */ |
| #define E1000_MANC_TCO_RESET 0x00010000 /* TCO Reset Occurred */ |
| #define E1000_MANC_RCV_TCO_EN 0x00020000 /* Receive TCO Packets Enabled */ |
| #define E1000_MANC_REPORT_STATUS 0x00040000 /* Status Reporting Enabled */ |
| #define E1000_MANC_RCV_ALL 0x00080000 /* Receive All Enabled */ |
| #define E1000_MANC_BLK_PHY_RST_ON_IDE 0x00040000 /* Block phy resets */ |
| /* Enable MAC address filtering */ |
| #define E1000_MANC_EN_MAC_ADDR_FILTER 0x00100000 |
| /* Enable MNG packets to host memory */ |
| #define E1000_MANC_EN_MNG2HOST 0x00200000 |
| /* Enable IP address filtering */ |
| #define E1000_MANC_EN_IP_ADDR_FILTER 0x00400000 |
| #define E1000_MANC_EN_XSUM_FILTER 0x00800000 /* Enable checksum filtering */ |
| #define E1000_MANC_BR_EN 0x01000000 /* Enable broadcast filtering */ |
| #define E1000_MANC_SMB_REQ 0x01000000 /* SMBus Request */ |
| #define E1000_MANC_SMB_GNT 0x02000000 /* SMBus Grant */ |
| #define E1000_MANC_SMB_CLK_IN 0x04000000 /* SMBus Clock In */ |
| #define E1000_MANC_SMB_DATA_IN 0x08000000 /* SMBus Data In */ |
| #define E1000_MANC_SMB_DATA_OUT 0x10000000 /* SMBus Data Out */ |
| #define E1000_MANC_SMB_CLK_OUT 0x20000000 /* SMBus Clock Out */ |
| |
| #define E1000_MANC_SMB_DATA_OUT_SHIFT 28 /* SMBus Data Out Shift */ |
| #define E1000_MANC_SMB_CLK_OUT_SHIFT 29 /* SMBus Clock Out Shift */ |
| |
| /* Receive Control */ |
| #define E1000_RCTL_RST 0x00000001 /* Software reset */ |
| #define E1000_RCTL_EN 0x00000002 /* enable */ |
| #define E1000_RCTL_SBP 0x00000004 /* store bad packet */ |
| #define E1000_RCTL_UPE 0x00000008 /* unicast promisc enable */ |
| #define E1000_RCTL_MPE 0x00000010 /* multicast promisc enable */ |
| #define E1000_RCTL_LPE 0x00000020 /* long packet enable */ |
| #define E1000_RCTL_LBM_NO 0x00000000 /* no loopback mode */ |
| #define E1000_RCTL_LBM_MAC 0x00000040 /* MAC loopback mode */ |
| #define E1000_RCTL_LBM_SLP 0x00000080 /* serial link loopback mode */ |
| #define E1000_RCTL_LBM_TCVR 0x000000C0 /* tcvr loopback mode */ |
| #define E1000_RCTL_DTYP_MASK 0x00000C00 /* Descriptor type mask */ |
| #define E1000_RCTL_DTYP_PS 0x00000400 /* Packet Split descriptor */ |
| #define E1000_RCTL_RDMTS_HALF 0x00000000 /* rx desc min thresh size */ |
| #define E1000_RCTL_RDMTS_QUAT 0x00000100 /* rx desc min thresh size */ |
| #define E1000_RCTL_RDMTS_EIGTH 0x00000200 /* rx desc min thresh size */ |
| #define E1000_RCTL_MO_SHIFT 12 /* multicast offset shift */ |
| #define E1000_RCTL_MO_0 0x00000000 /* multicast offset 11:0 */ |
| #define E1000_RCTL_MO_1 0x00001000 /* multicast offset 12:1 */ |
| #define E1000_RCTL_MO_2 0x00002000 /* multicast offset 13:2 */ |
| #define E1000_RCTL_MO_3 0x00003000 /* multicast offset 15:4 */ |
| #define E1000_RCTL_MDR 0x00004000 /* multicast desc ring 0 */ |
| #define E1000_RCTL_BAM 0x00008000 /* broadcast enable */ |
| /* these buffer sizes are valid if E1000_RCTL_BSEX is 0 */ |
| #define E1000_RCTL_SZ_2048 0x00000000 /* rx buffer size 2048 */ |
| #define E1000_RCTL_SZ_1024 0x00010000 /* rx buffer size 1024 */ |
| #define E1000_RCTL_SZ_512 0x00020000 /* rx buffer size 512 */ |
| #define E1000_RCTL_SZ_256 0x00030000 /* rx buffer size 256 */ |
| /* these buffer sizes are valid if E1000_RCTL_BSEX is 1 */ |
| #define E1000_RCTL_SZ_16384 0x00010000 /* rx buffer size 16384 */ |
| #define E1000_RCTL_SZ_8192 0x00020000 /* rx buffer size 8192 */ |
| #define E1000_RCTL_SZ_4096 0x00030000 /* rx buffer size 4096 */ |
| #define E1000_RCTL_VFE 0x00040000 /* vlan filter enable */ |
| #define E1000_RCTL_CFIEN 0x00080000 /* canonical form enable */ |
| #define E1000_RCTL_CFI 0x00100000 /* canonical form indicator */ |
| #define E1000_RCTL_DPF 0x00400000 /* discard pause frames */ |
| #define E1000_RCTL_PMCF 0x00800000 /* pass MAC control frames */ |
| #define E1000_RCTL_BSEX 0x02000000 /* Buffer size extension */ |
| #define E1000_RCTL_SECRC 0x04000000 /* Strip Ethernet CRC */ |
| #define E1000_RCTL_FLXBUF_MASK 0x78000000 /* Flexible buffer size */ |
| #define E1000_RCTL_FLXBUF_SHIFT 27 /* Flexible buffer shift */ |
| |
| /* |
| * Use byte values for the following shift parameters |
| * Usage: |
| * psrctl |= (((ROUNDUP(value0, 128) >> E1000_PSRCTL_BSIZE0_SHIFT) & |
| * E1000_PSRCTL_BSIZE0_MASK) | |
| * ((ROUNDUP(value1, 1024) >> E1000_PSRCTL_BSIZE1_SHIFT) & |
| * E1000_PSRCTL_BSIZE1_MASK) | |
| * ((ROUNDUP(value2, 1024) << E1000_PSRCTL_BSIZE2_SHIFT) & |
| * E1000_PSRCTL_BSIZE2_MASK) | |
| * ((ROUNDUP(value3, 1024) << E1000_PSRCTL_BSIZE3_SHIFT) |; |
| * E1000_PSRCTL_BSIZE3_MASK)) |
| * where value0 = [128..16256], default=256 |
| * value1 = [1024..64512], default=4096 |
| * value2 = [0..64512], default=4096 |
| * value3 = [0..64512], default=0 |
| */ |
| |
| #define E1000_PSRCTL_BSIZE0_MASK 0x0000007F |
| #define E1000_PSRCTL_BSIZE1_MASK 0x00003F00 |
| #define E1000_PSRCTL_BSIZE2_MASK 0x003F0000 |
| #define E1000_PSRCTL_BSIZE3_MASK 0x3F000000 |
| |
| #define E1000_PSRCTL_BSIZE0_SHIFT 7 /* Shift _right_ 7 */ |
| #define E1000_PSRCTL_BSIZE1_SHIFT 2 /* Shift _right_ 2 */ |
| #define E1000_PSRCTL_BSIZE2_SHIFT 6 /* Shift _left_ 6 */ |
| #define E1000_PSRCTL_BSIZE3_SHIFT 14 /* Shift _left_ 14 */ |
| |
| /* SWFW_SYNC Definitions */ |
| #define E1000_SWFW_EEP_SM 0x01 |
| #define E1000_SWFW_PHY0_SM 0x02 |
| #define E1000_SWFW_PHY1_SM 0x04 |
| #define E1000_SWFW_CSR_SM 0x08 |
| |
| /* FACTPS Definitions */ |
| #define E1000_FACTPS_LFS 0x40000000 /* LAN Function Select */ |
| /* Device Control */ |
| #define E1000_CTRL_FD 0x00000001 /* Full duplex.0=half; 1=full */ |
| #define E1000_CTRL_BEM 0x00000002 /* Endian Mode.0=little,1=big */ |
| #define E1000_CTRL_PRIOR 0x00000004 /* Priority on PCI. 0=rx,1=fair */ |
| #define E1000_CTRL_GIO_MASTER_DISABLE 0x00000004 /*Blocks new Master reqs */ |
| #define E1000_CTRL_LRST 0x00000008 /* Link reset. 0=normal,1=reset */ |
| #define E1000_CTRL_TME 0x00000010 /* Test mode. 0=normal,1=test */ |
| #define E1000_CTRL_SLE 0x00000020 /* Serial Link on 0=dis,1=en */ |
| #define E1000_CTRL_ASDE 0x00000020 /* Auto-speed detect enable */ |
| #define E1000_CTRL_SLU 0x00000040 /* Set link up (Force Link) */ |
| #define E1000_CTRL_ILOS 0x00000080 /* Invert Loss-Of Signal */ |
| #define E1000_CTRL_SPD_SEL 0x00000300 /* Speed Select Mask */ |
| #define E1000_CTRL_SPD_10 0x00000000 /* Force 10Mb */ |
| #define E1000_CTRL_SPD_100 0x00000100 /* Force 100Mb */ |
| #define E1000_CTRL_SPD_1000 0x00000200 /* Force 1Gb */ |
| #define E1000_CTRL_BEM32 0x00000400 /* Big Endian 32 mode */ |
| #define E1000_CTRL_FRCSPD 0x00000800 /* Force Speed */ |
| #define E1000_CTRL_FRCDPX 0x00001000 /* Force Duplex */ |
| #define E1000_CTRL_D_UD_EN 0x00002000 /* Dock/Undock enable */ |
| #define E1000_CTRL_D_UD_POLARITY 0x00004000 /* Defined polarity of Dock/Undock |
| * indication in SDP[0] */ |
| #define E1000_CTRL_FORCE_PHY_RESET 0x00008000 /* Reset both PHY ports, through |
| * PHYRST_N pin */ |
| #define E1000_CTRL_EXT_LINK_EN 0x00010000 /* enable link status from external |
| * LINK_0 and LINK_1 pins */ |
| #define E1000_CTRL_SWDPIN0 0x00040000 /* SWDPIN 0 value */ |
| #define E1000_CTRL_SWDPIN1 0x00080000 /* SWDPIN 1 value */ |
| #define E1000_CTRL_SWDPIN2 0x00100000 /* SWDPIN 2 value */ |
| #define E1000_CTRL_SWDPIN3 0x00200000 /* SWDPIN 3 value */ |
| #define E1000_CTRL_SWDPIO0 0x00400000 /* SWDPIN 0 Input or output */ |
| #define E1000_CTRL_SWDPIO1 0x00800000 /* SWDPIN 1 input or output */ |
| #define E1000_CTRL_SWDPIO2 0x01000000 /* SWDPIN 2 input or output */ |
| #define E1000_CTRL_SWDPIO3 0x02000000 /* SWDPIN 3 input or output */ |
| #define E1000_CTRL_RST 0x04000000 /* Global reset */ |
| #define E1000_CTRL_RFCE 0x08000000 /* Receive Flow Control enable */ |
| #define E1000_CTRL_TFCE 0x10000000 /* Transmit flow control enable */ |
| #define E1000_CTRL_RTE 0x20000000 /* Routing tag enable */ |
| #define E1000_CTRL_VME 0x40000000 /* IEEE VLAN mode enable */ |
| #define E1000_CTRL_PHY_RST 0x80000000 /* PHY Reset */ |
| #define E1000_CTRL_SW2FW_INT 0x02000000 /* Initiate an interrupt to ME */ |
| #define E1000_CTRL_I2C_ENA 0x02000000 /* I2C enable */ |
| |
| /* |
| * Bit definitions for the Management Data IO (MDIO) and Management Data |
| * Clock (MDC) pins in the Device Control Register. |
| */ |
| #define E1000_CTRL_PHY_RESET_DIR E1000_CTRL_SWDPIO0 |
| #define E1000_CTRL_PHY_RESET E1000_CTRL_SWDPIN0 |
| #define E1000_CTRL_MDIO_DIR E1000_CTRL_SWDPIO2 |
| #define E1000_CTRL_MDIO E1000_CTRL_SWDPIN2 |
| #define E1000_CTRL_MDC_DIR E1000_CTRL_SWDPIO3 |
| #define E1000_CTRL_MDC E1000_CTRL_SWDPIN3 |
| #define E1000_CTRL_PHY_RESET_DIR4 E1000_CTRL_EXT_SDP4_DIR |
| #define E1000_CTRL_PHY_RESET4 E1000_CTRL_EXT_SDP4_DATA |
| |
| #define E1000_CONNSW_ENRGSRC 0x4 |
| #define E1000_PCS_CFG_PCS_EN 8 |
| #define E1000_PCS_LCTL_FLV_LINK_UP 1 |
| #define E1000_PCS_LCTL_FSV_10 0 |
| #define E1000_PCS_LCTL_FSV_100 2 |
| #define E1000_PCS_LCTL_FSV_1000 4 |
| #define E1000_PCS_LCTL_FDV_FULL 8 |
| #define E1000_PCS_LCTL_FSD 0x10 |
| #define E1000_PCS_LCTL_FORCE_LINK 0x20 |
| #define E1000_PCS_LCTL_LOW_LINK_LATCH 0x40 |
| #define E1000_PCS_LCTL_FORCE_FCTRL 0x80 |
| #define E1000_PCS_LCTL_AN_ENABLE 0x10000 |
| #define E1000_PCS_LCTL_AN_RESTART 0x20000 |
| #define E1000_PCS_LCTL_AN_TIMEOUT 0x40000 |
| #define E1000_PCS_LCTL_AN_SGMII_BYPASS 0x80000 |
| #define E1000_PCS_LCTL_AN_SGMII_TRIGGER 0x100000 |
| #define E1000_PCS_LCTL_FAST_LINK_TIMER 0x1000000 |
| #define E1000_PCS_LCTL_LINK_OK_FIX 0x2000000 |
| #define E1000_PCS_LCTL_CRS_ON_NI 0x4000000 |
| #define E1000_ENABLE_SERDES_LOOPBACK 0x0410 |
| |
| #define E1000_PCS_LSTS_LINK_OK 1 |
| #define E1000_PCS_LSTS_SPEED_10 0 |
| #define E1000_PCS_LSTS_SPEED_100 2 |
| #define E1000_PCS_LSTS_SPEED_1000 4 |
| #define E1000_PCS_LSTS_DUPLEX_FULL 8 |
| #define E1000_PCS_LSTS_SYNK_OK 0x10 |
| #define E1000_PCS_LSTS_AN_COMPLETE 0x10000 |
| #define E1000_PCS_LSTS_AN_PAGE_RX 0x20000 |
| #define E1000_PCS_LSTS_AN_TIMED_OUT 0x40000 |
| #define E1000_PCS_LSTS_AN_REMOTE_FAULT 0x80000 |
| #define E1000_PCS_LSTS_AN_ERROR_RWS 0x100000 |
| |
| /* Device Status */ |
| #define E1000_STATUS_FD 0x00000001 /* Full duplex.0=half,1=full */ |
| #define E1000_STATUS_LU 0x00000002 /* Link up.0=no,1=link */ |
| #define E1000_STATUS_FUNC_MASK 0x0000000C /* PCI Function Mask */ |
| #define E1000_STATUS_FUNC_SHIFT 2 |
| #define E1000_STATUS_FUNC_0 0x00000000 /* Function 0 */ |
| #define E1000_STATUS_FUNC_1 0x00000004 /* Function 1 */ |
| #define E1000_STATUS_TXOFF 0x00000010 /* transmission paused */ |
| #define E1000_STATUS_TBIMODE 0x00000020 /* TBI mode */ |
| #define E1000_STATUS_SPEED_MASK 0x000000C0 |
| #define E1000_STATUS_SPEED_10 0x00000000 /* Speed 10Mb/s */ |
| #define E1000_STATUS_SPEED_100 0x00000040 /* Speed 100Mb/s */ |
| #define E1000_STATUS_SPEED_1000 0x00000080 /* Speed 1000Mb/s */ |
| #define E1000_STATUS_LAN_INIT_DONE 0x00000200 /* Lan Init Completion by NVM */ |
| #define E1000_STATUS_ASDV 0x00000300 /* Auto speed detect value */ |
| #define E1000_STATUS_PHYRA 0x00000400 /* PHY Reset Asserted */ |
| #define E1000_STATUS_DOCK_CI 0x00000800 /* Change in Dock/Undock state. |
| * Clear on write '0'. */ |
| #define E1000_STATUS_GIO_MASTER_ENABLE 0x00080000 /* Master request status */ |
| #define E1000_STATUS_MTXCKOK 0x00000400 /* MTX clock running OK */ |
| #define E1000_STATUS_PCI66 0x00000800 /* In 66Mhz slot */ |
| #define E1000_STATUS_BUS64 0x00001000 /* In 64 bit slot */ |
| #define E1000_STATUS_PCIX_MODE 0x00002000 /* PCI-X mode */ |
| #define E1000_STATUS_PCIX_SPEED 0x0000C000 /* PCI-X bus speed */ |
| #define E1000_STATUS_BMC_SKU_0 0x00100000 /* BMC USB redirect disabled */ |
| #define E1000_STATUS_BMC_SKU_1 0x00200000 /* BMC SRAM disabled */ |
| #define E1000_STATUS_BMC_SKU_2 0x00400000 /* BMC SDRAM disabled */ |
| #define E1000_STATUS_BMC_CRYPTO 0x00800000 /* BMC crypto disabled */ |
| #define E1000_STATUS_BMC_LITE 0x01000000 /* BMC external code execution |
| * disabled */ |
| #define E1000_STATUS_RGMII_ENABLE 0x02000000 /* RGMII disabled */ |
| #define E1000_STATUS_FUSE_8 0x04000000 |
| #define E1000_STATUS_FUSE_9 0x08000000 |
| #define E1000_STATUS_SERDES0_DIS 0x10000000 /* SERDES disabled on port 0 */ |
| #define E1000_STATUS_SERDES1_DIS 0x20000000 /* SERDES disabled on port 1 */ |
| |
| /* Constants used to interpret the masked PCI-X bus speed. */ |
| #define E1000_STATUS_PCIX_SPEED_66 0x00000000 /* PCI-X bus speed 50-66 MHz */ |
| #define E1000_STATUS_PCIX_SPEED_100 0x00004000 /* PCI-X bus speed 66-100 MHz */ |
| #define E1000_STATUS_PCIX_SPEED_133 0x00008000 /*PCI-X bus speed 100-133 MHz */ |
| |
| #define SPEED_10 10 |
| #define SPEED_100 100 |
| #define SPEED_1000 1000 |
| #define HALF_DUPLEX 1 |
| #define FULL_DUPLEX 2 |
| |
| #define PHY_FORCE_TIME 20 |
| |
| #define ADVERTISE_10_HALF 0x0001 |
| #define ADVERTISE_10_FULL 0x0002 |
| #define ADVERTISE_100_HALF 0x0004 |
| #define ADVERTISE_100_FULL 0x0008 |
| #define ADVERTISE_1000_HALF 0x0010 /* Not used, just FYI */ |
| #define ADVERTISE_1000_FULL 0x0020 |
| |
| /* 1000/H is not supported, nor spec-compliant. */ |
| #define E1000_ALL_SPEED_DUPLEX (ADVERTISE_10_HALF | ADVERTISE_10_FULL | \ |
| ADVERTISE_100_HALF | ADVERTISE_100_FULL | \ |
| ADVERTISE_1000_FULL) |
| #define E1000_ALL_NOT_GIG (ADVERTISE_10_HALF | ADVERTISE_10_FULL | \ |
| ADVERTISE_100_HALF | ADVERTISE_100_FULL) |
| #define E1000_ALL_100_SPEED (ADVERTISE_100_HALF | ADVERTISE_100_FULL) |
| #define E1000_ALL_10_SPEED (ADVERTISE_10_HALF | ADVERTISE_10_FULL) |
| #define E1000_ALL_FULL_DUPLEX (ADVERTISE_10_FULL | ADVERTISE_100_FULL | \ |
| ADVERTISE_1000_FULL) |
| #define E1000_ALL_HALF_DUPLEX (ADVERTISE_10_HALF | ADVERTISE_100_HALF) |
| |
| #define AUTONEG_ADVERTISE_SPEED_DEFAULT E1000_ALL_SPEED_DUPLEX |
| |
| /* LED Control */ |
| #define E1000_LEDCTL_LED0_MODE_MASK 0x0000000F |
| #define E1000_LEDCTL_LED0_MODE_SHIFT 0 |
| #define E1000_LEDCTL_LED0_BLINK_RATE 0x00000020 |
| #define E1000_LEDCTL_LED0_IVRT 0x00000040 |
| #define E1000_LEDCTL_LED0_BLINK 0x00000080 |
| #define E1000_LEDCTL_LED1_MODE_MASK 0x00000F00 |
| #define E1000_LEDCTL_LED1_MODE_SHIFT 8 |
| #define E1000_LEDCTL_LED1_BLINK_RATE 0x00002000 |
| #define E1000_LEDCTL_LED1_IVRT 0x00004000 |
| #define E1000_LEDCTL_LED1_BLINK 0x00008000 |
| #define E1000_LEDCTL_LED2_MODE_MASK 0x000F0000 |
| #define E1000_LEDCTL_LED2_MODE_SHIFT 16 |
| #define E1000_LEDCTL_LED2_BLINK_RATE 0x00200000 |
| #define E1000_LEDCTL_LED2_IVRT 0x00400000 |
| #define E1000_LEDCTL_LED2_BLINK 0x00800000 |
| #define E1000_LEDCTL_LED3_MODE_MASK 0x0F000000 |
| #define E1000_LEDCTL_LED3_MODE_SHIFT 24 |
| #define E1000_LEDCTL_LED3_BLINK_RATE 0x20000000 |
| #define E1000_LEDCTL_LED3_IVRT 0x40000000 |
| #define E1000_LEDCTL_LED3_BLINK 0x80000000 |
| |
| #define E1000_LEDCTL_MODE_LINK_10_1000 0x0 |
| #define E1000_LEDCTL_MODE_LINK_100_1000 0x1 |
| #define E1000_LEDCTL_MODE_LINK_UP 0x2 |
| #define E1000_LEDCTL_MODE_ACTIVITY 0x3 |
| #define E1000_LEDCTL_MODE_LINK_ACTIVITY 0x4 |
| #define E1000_LEDCTL_MODE_LINK_10 0x5 |
| #define E1000_LEDCTL_MODE_LINK_100 0x6 |
| #define E1000_LEDCTL_MODE_LINK_1000 0x7 |
| #define E1000_LEDCTL_MODE_PCIX_MODE 0x8 |
| #define E1000_LEDCTL_MODE_FULL_DUPLEX 0x9 |
| #define E1000_LEDCTL_MODE_COLLISION 0xA |
| #define E1000_LEDCTL_MODE_BUS_SPEED 0xB |
| #define E1000_LEDCTL_MODE_BUS_SIZE 0xC |
| #define E1000_LEDCTL_MODE_PAUSED 0xD |
| #define E1000_LEDCTL_MODE_LED_ON 0xE |
| #define E1000_LEDCTL_MODE_LED_OFF 0xF |
| |
| /* Transmit Descriptor bit definitions */ |
| #define E1000_TXD_DTYP_D 0x00100000 /* Data Descriptor */ |
| #define E1000_TXD_DTYP_C 0x00000000 /* Context Descriptor */ |
| #define E1000_TXD_POPTS_SHIFT 8 /* POPTS shift */ |
| #define E1000_TXD_POPTS_IXSM 0x01 /* Insert IP checksum */ |
| #define E1000_TXD_POPTS_TXSM 0x02 /* Insert TCP/UDP checksum */ |
| #define E1000_TXD_CMD_EOP 0x01000000 /* End of Packet */ |
| #define E1000_TXD_CMD_IFCS 0x02000000 /* Insert FCS (Ethernet CRC) */ |
| #define E1000_TXD_CMD_IC 0x04000000 /* Insert Checksum */ |
| #define E1000_TXD_CMD_RS 0x08000000 /* Report Status */ |
| #define E1000_TXD_CMD_RPS 0x10000000 /* Report Packet Sent */ |
| #define E1000_TXD_CMD_DEXT 0x20000000 /* Descriptor extension (0 = legacy) */ |
| #define E1000_TXD_CMD_VLE 0x40000000 /* Add VLAN tag */ |
| #define E1000_TXD_CMD_IDE 0x80000000 /* Enable Tidv register */ |
| #define E1000_TXD_STAT_DD 0x00000001 /* Descriptor Done */ |
| #define E1000_TXD_STAT_EC 0x00000002 /* Excess Collisions */ |
| #define E1000_TXD_STAT_LC 0x00000004 /* Late Collisions */ |
| #define E1000_TXD_STAT_TU 0x00000008 /* Transmit underrun */ |
| #define E1000_TXD_CMD_TCP 0x01000000 /* TCP packet */ |
| #define E1000_TXD_CMD_IP 0x02000000 /* IP packet */ |
| #define E1000_TXD_CMD_TSE 0x04000000 /* TCP Seg enable */ |
| #define E1000_TXD_STAT_TC 0x00000004 /* Tx Underrun */ |
| /* Extended desc bits for Linksec and timesync */ |
| |
| /* Transmit Control */ |
| #define E1000_TCTL_RST 0x00000001 /* software reset */ |
| #define E1000_TCTL_EN 0x00000002 /* enable tx */ |
| #define E1000_TCTL_BCE 0x00000004 /* busy check enable */ |
| #define E1000_TCTL_PSP 0x00000008 /* pad short packets */ |
| #define E1000_TCTL_CT 0x00000ff0 /* collision threshold */ |
| #define E1000_TCTL_COLD 0x003ff000 /* collision distance */ |
| #define E1000_TCTL_SWXOFF 0x00400000 /* SW Xoff transmission */ |
| #define E1000_TCTL_PBE 0x00800000 /* Packet Burst Enable */ |
| #define E1000_TCTL_RTLC 0x01000000 /* Re-transmit on late collision */ |
| #define E1000_TCTL_NRTU 0x02000000 /* No Re-transmit on underrun */ |
| #define E1000_TCTL_MULR 0x10000000 /* Multiple request support */ |
| |
| /* Transmit Arbitration Count */ |
| #define E1000_TARC0_ENABLE 0x00000400 /* Enable Tx Queue 0 */ |
| |
| /* SerDes Control */ |
| #define E1000_SCTL_DISABLE_SERDES_LOOPBACK 0x0400 |
| |
| /* Receive Checksum Control */ |
| #define E1000_RXCSUM_PCSS_MASK 0x000000FF /* Packet Checksum Start */ |
| #define E1000_RXCSUM_IPOFL 0x00000100 /* IPv4 checksum offload */ |
| #define E1000_RXCSUM_TUOFL 0x00000200 /* TCP / UDP checksum offload */ |
| #define E1000_RXCSUM_IPV6OFL 0x00000400 /* IPv6 checksum offload */ |
| #define E1000_RXCSUM_CRCOFL 0x00000800 /* CRC32 offload enable */ |
| #define E1000_RXCSUM_IPPCSE 0x00001000 /* IP payload checksum enable */ |
| #define E1000_RXCSUM_PCSD 0x00002000 /* packet checksum disabled */ |
| |
| /* Header split receive */ |
| #define E1000_RFCTL_ISCSI_DIS 0x00000001 |
| #define E1000_RFCTL_ISCSI_DWC_MASK 0x0000003E |
| #define E1000_RFCTL_ISCSI_DWC_SHIFT 1 |
| #define E1000_RFCTL_NFSW_DIS 0x00000040 |
| #define E1000_RFCTL_NFSR_DIS 0x00000080 |
| #define E1000_RFCTL_NFS_VER_MASK 0x00000300 |
| #define E1000_RFCTL_NFS_VER_SHIFT 8 |
| #define E1000_RFCTL_IPV6_DIS 0x00000400 |
| #define E1000_RFCTL_IPV6_XSUM_DIS 0x00000800 |
| #define E1000_RFCTL_ACK_DIS 0x00001000 |
| #define E1000_RFCTL_ACKD_DIS 0x00002000 |
| #define E1000_RFCTL_IPFRSP_DIS 0x00004000 |
| #define E1000_RFCTL_EXTEN 0x00008000 |
| #define E1000_RFCTL_IPV6_EX_DIS 0x00010000 |
| #define E1000_RFCTL_NEW_IPV6_EXT_DIS 0x00020000 |
| #define E1000_RFCTL_LEF 0x00040000 |
| |
| /* Collision related configuration parameters */ |
| #define E1000_COLLISION_THRESHOLD 15 |
| #define E1000_CT_SHIFT 4 |
| #define E1000_COLLISION_DISTANCE 63 |
| #define E1000_COLD_SHIFT 12 |
| |
| /* Default values for the transmit IPG register */ |
| #define DEFAULT_82542_TIPG_IPGT 10 |
| #define DEFAULT_82543_TIPG_IPGT_FIBER 9 |
| #define DEFAULT_82543_TIPG_IPGT_COPPER 8 |
| |
| #define E1000_TIPG_IPGT_MASK 0x000003FF |
| #define E1000_TIPG_IPGR1_MASK 0x000FFC00 |
| #define E1000_TIPG_IPGR2_MASK 0x3FF00000 |
| |
| #define DEFAULT_82542_TIPG_IPGR1 2 |
| #define DEFAULT_82543_TIPG_IPGR1 8 |
| #define E1000_TIPG_IPGR1_SHIFT 10 |
| |
| #define DEFAULT_82542_TIPG_IPGR2 10 |
| #define DEFAULT_82543_TIPG_IPGR2 6 |
| #define DEFAULT_80003ES2LAN_TIPG_IPGR2 7 |
| #define E1000_TIPG_IPGR2_SHIFT 20 |
| |
| /* Ethertype field values */ |
| #define ETHERNET_IEEE_VLAN_TYPE 0x8100 /* 802.3ac packet */ |
| |
| #define ETHERNET_FCS_SIZE 4 |
| #define MAX_JUMBO_FRAME_SIZE 0x3F00 |
| |
| /* Extended Configuration Control and Size */ |
| #define E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP 0x00000020 |
| #define E1000_EXTCNF_CTRL_LCD_WRITE_ENABLE 0x00000001 |
| #define E1000_EXTCNF_CTRL_SWFLAG 0x00000020 |
| #define E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH_MASK 0x00FF0000 |
| #define E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH_SHIFT 16 |
| #define E1000_EXTCNF_CTRL_EXT_CNF_POINTER_MASK 0x0FFF0000 |
| #define E1000_EXTCNF_CTRL_EXT_CNF_POINTER_SHIFT 16 |
| |
| #define E1000_PHY_CTRL_SPD_EN 0x00000001 |
| #define E1000_PHY_CTRL_D0A_LPLU 0x00000002 |
| #define E1000_PHY_CTRL_NOND0A_LPLU 0x00000004 |
| #define E1000_PHY_CTRL_NOND0A_GBE_DISABLE 0x00000008 |
| #define E1000_PHY_CTRL_GBE_DISABLE 0x00000040 |
| |
| #define E1000_KABGTXD_BGSQLBIAS 0x00050000 |
| |
| /* PBA constants */ |
| #define E1000_PBA_6K 0x0006 /* 6KB */ |
| #define E1000_PBA_8K 0x0008 /* 8KB */ |
| #define E1000_PBA_10K 0x000A /* 10KB */ |
| #define E1000_PBA_12K 0x000C /* 12KB */ |
| #define E1000_PBA_14K 0x000E /* 14KB */ |
| #define E1000_PBA_16K 0x0010 /* 16KB */ |
| #define E1000_PBA_18K 0x0012 |
| #define E1000_PBA_20K 0x0014 |
| #define E1000_PBA_22K 0x0016 |
| #define E1000_PBA_24K 0x0018 |
| #define E1000_PBA_26K 0x001A |
| #define E1000_PBA_30K 0x001E |
| #define E1000_PBA_32K 0x0020 |
| #define E1000_PBA_34K 0x0022 |
| #define E1000_PBA_35K 0x0023 |
| #define E1000_PBA_38K 0x0026 |
| #define E1000_PBA_40K 0x0028 |
| #define E1000_PBA_48K 0x0030 /* 48KB */ |
| #define E1000_PBA_64K 0x0040 /* 64KB */ |
| |
| #define E1000_PBS_16K E1000_PBA_16K |
| #define E1000_PBS_24K E1000_PBA_24K |
| |
| #define IFS_MAX 80 |
| #define IFS_MIN 40 |
| #define IFS_RATIO 4 |
| #define IFS_STEP 10 |
| #define MIN_NUM_XMITS 1000 |
| |
| /* SW Semaphore Register */ |
| #define E1000_SWSM_SMBI 0x00000001 /* Driver Semaphore bit */ |
| #define E1000_SWSM_SWESMBI 0x00000002 /* FW Semaphore bit */ |
| #define E1000_SWSM_WMNG 0x00000004 /* Wake MNG Clock */ |
| #define E1000_SWSM_DRV_LOAD 0x00000008 /* Driver Loaded Bit */ |
| |
| #define E1000_SWSM2_LOCK 0x00000002 /* Secondary driver semaphore bit */ |
| |
| /* Interrupt Cause Read */ |
| #define E1000_ICR_TXDW 0x00000001 /* Transmit desc written back */ |
| #define E1000_ICR_TXQE 0x00000002 /* Transmit Queue empty */ |
| #define E1000_ICR_LSC 0x00000004 /* Link Status Change */ |
| #define E1000_ICR_RXSEQ 0x00000008 /* rx sequence error */ |
| #define E1000_ICR_RXDMT0 0x00000010 /* rx desc min. threshold (0) */ |
| #define E1000_ICR_RXO 0x00000040 /* rx overrun */ |
| #define E1000_ICR_RXT0 0x00000080 /* rx timer intr (ring 0) */ |
| #define E1000_ICR_VMMB 0x00000100 /* VM MB event */ |
| #define E1000_ICR_MDAC 0x00000200 /* MDIO access complete */ |
| #define E1000_ICR_RXCFG 0x00000400 /* Rx /c/ ordered set */ |
| #define E1000_ICR_GPI_EN0 0x00000800 /* GP Int 0 */ |
| #define E1000_ICR_GPI_EN1 0x00001000 /* GP Int 1 */ |
| #define E1000_ICR_GPI_EN2 0x00002000 /* GP Int 2 */ |
| #define E1000_ICR_GPI_EN3 0x00004000 /* GP Int 3 */ |
| #define E1000_ICR_TXD_LOW 0x00008000 |
| #define E1000_ICR_SRPD 0x00010000 |
| #define E1000_ICR_ACK 0x00020000 /* Receive Ack frame */ |
| #define E1000_ICR_MNG 0x00040000 /* Manageability event */ |
| #define E1000_ICR_DOCK 0x00080000 /* Dock/Undock */ |
| #define E1000_ICR_INT_ASSERTED 0x80000000 /* If this bit asserted, the driver |
| * should claim the interrupt */ |
| #define E1000_ICR_RXD_FIFO_PAR0 0x00100000 /* Q0 Rx desc FIFO parity error */ |
| #define E1000_ICR_TXD_FIFO_PAR0 0x00200000 /* Q0 Tx desc FIFO parity error */ |
| #define E1000_ICR_HOST_ARB_PAR 0x00400000 /* host arb read buffer parity err */ |
| #define E1000_ICR_PB_PAR 0x00800000 /* packet buffer parity error */ |
| #define E1000_ICR_RXD_FIFO_PAR1 0x01000000 /* Q1 Rx desc FIFO parity error */ |
| #define E1000_ICR_TXD_FIFO_PAR1 0x02000000 /* Q1 Tx desc FIFO parity error */ |
| #define E1000_ICR_ALL_PARITY 0x03F00000 /* all parity error bits */ |
| #define E1000_ICR_DSW 0x00000020 /* FW changed the status of DISSW |
| * bit in the FWSM */ |
| #define E1000_ICR_PHYINT 0x00001000 /* LAN connected device generates |
| * an interrupt */ |
| #define E1000_ICR_DOUTSYNC 0x10000000 /* NIC DMA out of sync */ |
| #define E1000_ICR_EPRST 0x00100000 /* ME hardware reset occurs */ |
| |
| /* |
| * This defines the bits that are set in the Interrupt Mask |
| * Set/Read Register. Each bit is documented below: |
| * o RXDMT0 = Receive Descriptor Minimum Threshold hit (ring 0) |
| * o RXSEQ = Receive Sequence Error |
| */ |
| #define POLL_IMS_ENABLE_MASK ( \ |
| E1000_IMS_RXDMT0 | \ |
| E1000_IMS_RXSEQ) |
| |
| /* |
| * This defines the bits that are set in the Interrupt Mask |
| * Set/Read Register. Each bit is documented below: |
| * o RXT0 = Receiver Timer Interrupt (ring 0) |
| * o TXDW = Transmit Descriptor Written Back |
| * o RXDMT0 = Receive Descriptor Minimum Threshold hit (ring 0) |
| * o RXSEQ = Receive Sequence Error |
| * o LSC = Link Status Change |
| */ |
| #define IMS_ENABLE_MASK ( \ |
| E1000_IMS_RXT0 | \ |
| E1000_IMS_TXDW | \ |
| E1000_IMS_RXDMT0 | \ |
| E1000_IMS_RXSEQ | \ |
| E1000_IMS_LSC) |
| |
| /* Interrupt Mask Set */ |
| #define E1000_IMS_TXDW E1000_ICR_TXDW /* Tx desc written back */ |
| #define E1000_IMS_TXQE E1000_ICR_TXQE /* Transmit Queue empty */ |
| #define E1000_IMS_LSC E1000_ICR_LSC /* Link Status Change */ |
| #define E1000_IMS_VMMB E1000_ICR_VMMB /* Mail box activity */ |
| #define E1000_IMS_RXSEQ E1000_ICR_RXSEQ /* rx sequence error */ |
| #define E1000_IMS_RXDMT0 E1000_ICR_RXDMT0 /* rx desc min. threshold */ |
| #define E1000_IMS_RXO E1000_ICR_RXO /* rx overrun */ |
| #define E1000_IMS_RXT0 E1000_ICR_RXT0 /* rx timer intr */ |
| #define E1000_IMS_MDAC E1000_ICR_MDAC /* MDIO access complete */ |
| #define E1000_IMS_RXCFG E1000_ICR_RXCFG /* Rx /c/ ordered set */ |
| #define E1000_IMS_GPI_EN0 E1000_ICR_GPI_EN0 /* GP Int 0 */ |
| #define E1000_IMS_GPI_EN1 E1000_ICR_GPI_EN1 /* GP Int 1 */ |
| #define E1000_IMS_GPI_EN2 E1000_ICR_GPI_EN2 /* GP Int 2 */ |
| #define E1000_IMS_GPI_EN3 E1000_ICR_GPI_EN3 /* GP Int 3 */ |
| #define E1000_IMS_TXD_LOW E1000_ICR_TXD_LOW |
| #define E1000_IMS_SRPD E1000_ICR_SRPD |
| #define E1000_IMS_ACK E1000_ICR_ACK /* Receive Ack frame */ |
| #define E1000_IMS_MNG E1000_ICR_MNG /* Manageability event */ |
| #define E1000_IMS_DOCK E1000_ICR_DOCK /* Dock/Undock */ |
| #define E1000_IMS_RXD_FIFO_PAR0 E1000_ICR_RXD_FIFO_PAR0 /* Q0 Rx desc FIFO |
| * parity error */ |
| #define E1000_IMS_TXD_FIFO_PAR0 E1000_ICR_TXD_FIFO_PAR0 /* Q0 Tx desc FIFO |
| * parity error */ |
| #define E1000_IMS_HOST_ARB_PAR E1000_ICR_HOST_ARB_PAR /* host arb read buffer |
| * parity error */ |
| #define E1000_IMS_PB_PAR E1000_ICR_PB_PAR /* packet buffer parity |
| * error */ |
| #define E1000_IMS_RXD_FIFO_PAR1 E1000_ICR_RXD_FIFO_PAR1 /* Q1 Rx desc FIFO |
| * parity error */ |
| #define E1000_IMS_TXD_FIFO_PAR1 E1000_ICR_TXD_FIFO_PAR1 /* Q1 Tx desc FIFO |
| * parity error */ |
| #define E1000_IMS_DSW E1000_ICR_DSW |
| #define E1000_IMS_PHYINT E1000_ICR_PHYINT |
| #define E1000_IMS_DOUTSYNC E1000_ICR_DOUTSYNC /* NIC DMA out of sync */ |
| #define E1000_IMS_EPRST E1000_ICR_EPRST |
| |
| /* Interrupt Cause Set */ |
| #define E1000_ICS_TXDW E1000_ICR_TXDW /* Tx desc written back */ |
| #define E1000_ICS_TXQE E1000_ICR_TXQE /* Transmit Queue empty */ |
| #define E1000_ICS_LSC E1000_ICR_LSC /* Link Status Change */ |
| #define E1000_ICS_RXSEQ E1000_ICR_RXSEQ /* rx sequence error */ |
| #define E1000_ICS_RXDMT0 E1000_ICR_RXDMT0 /* rx desc min. threshold */ |
| #define E1000_ICS_RXO E1000_ICR_RXO /* rx overrun */ |
| #define E1000_ICS_RXT0 E1000_ICR_RXT0 /* rx timer intr */ |
| #define E1000_ICS_MDAC E1000_ICR_MDAC /* MDIO access complete */ |
| #define E1000_ICS_RXCFG E1000_ICR_RXCFG /* Rx /c/ ordered set */ |
| #define E1000_ICS_GPI_EN0 E1000_ICR_GPI_EN0 /* GP Int 0 */ |
| #define E1000_ICS_GPI_EN1 E1000_ICR_GPI_EN1 /* GP Int 1 */ |
| #define E1000_ICS_GPI_EN2 E1000_ICR_GPI_EN2 /* GP Int 2 */ |
| #define E1000_ICS_GPI_EN3 E1000_ICR_GPI_EN3 /* GP Int 3 */ |
| #define E1000_ICS_TXD_LOW E1000_ICR_TXD_LOW |
| #define E1000_ICS_SRPD E1000_ICR_SRPD |
| #define E1000_ICS_ACK E1000_ICR_ACK /* Receive Ack frame */ |
| #define E1000_ICS_MNG E1000_ICR_MNG /* Manageability event */ |
| #define E1000_ICS_DOCK E1000_ICR_DOCK /* Dock/Undock */ |
| #define E1000_ICS_RXD_FIFO_PAR0 E1000_ICR_RXD_FIFO_PAR0 /* Q0 Rx desc FIFO |
| * parity error */ |
| #define E1000_ICS_TXD_FIFO_PAR0 E1000_ICR_TXD_FIFO_PAR0 /* Q0 Tx desc FIFO |
| * parity error */ |
| #define E1000_ICS_HOST_ARB_PAR E1000_ICR_HOST_ARB_PAR /* host arb read buffer |
| * parity error */ |
| #define E1000_ICS_PB_PAR E1000_ICR_PB_PAR /* packet buffer parity |
| * error */ |
| #define E1000_ICS_RXD_FIFO_PAR1 E1000_ICR_RXD_FIFO_PAR1 /* Q1 Rx desc FIFO |
| * parity error */ |
| #define E1000_ICS_TXD_FIFO_PAR1 E1000_ICR_TXD_FIFO_PAR1 /* Q1 Tx desc FIFO |
| * parity error */ |
| #define E1000_ICS_DSW E1000_ICR_DSW |
| #define E1000_ICS_DOUTSYNC E1000_ICR_DOUTSYNC /* NIC DMA out of sync */ |
| #define E1000_ICS_PHYINT E1000_ICR_PHYINT |
| #define E1000_ICS_EPRST E1000_ICR_EPRST |
| |
| /* Transmit Descriptor Control */ |
| #define E1000_TXDCTL_PTHRESH 0x0000003F /* TXDCTL Prefetch Threshold */ |
| #define E1000_TXDCTL_HTHRESH 0x00003F00 /* TXDCTL Host Threshold */ |
| #define E1000_TXDCTL_WTHRESH 0x003F0000 /* TXDCTL Writeback Threshold */ |
| #define E1000_TXDCTL_GRAN 0x01000000 /* TXDCTL Granularity */ |
| #define E1000_TXDCTL_LWTHRESH 0xFE000000 /* TXDCTL Low Threshold */ |
| #define E1000_TXDCTL_FULL_TX_DESC_WB 0x01010000 /* GRAN=1, WTHRESH=1 */ |
| #define E1000_TXDCTL_MAX_TX_DESC_PREFETCH 0x0100001F /* GRAN=1, PTHRESH=31 */ |
| /* Enable the counting of descriptors still to be processed. */ |
| #define E1000_TXDCTL_COUNT_DESC 0x00400000 |
| |
| /* Flow Control Constants */ |
| #define FLOW_CONTROL_ADDRESS_LOW 0x00C28001 |
| #define FLOW_CONTROL_ADDRESS_HIGH 0x00000100 |
| #define FLOW_CONTROL_TYPE 0x8808 |
| |
| /* 802.1q VLAN Packet Size */ |
| #define VLAN_TAG_SIZE 4 /* 802.3ac tag (not DMA'd) */ |
| #define E1000_VLAN_FILTER_TBL_SIZE 128 /* VLAN Filter Table (4096 bits) */ |
| |
| /* Receive Address */ |
| /* |
| * Number of high/low register pairs in the RAR. The RAR (Receive Address |
| * Registers) holds the directed and multicast addresses that we monitor. |
| * Technically, we have 16 spots. However, we reserve one of these spots |
| * (RAR[15]) for our directed address used by controllers with |
| * manageability enabled, allowing us room for 15 multicast addresses. |
| */ |
| #define E1000_RAR_ENTRIES 15 |
| #define E1000_RAH_AV 0x80000000 /* Receive descriptor valid */ |
| #define E1000_RAL_MAC_ADDR_LEN 4 |
| #define E1000_RAH_MAC_ADDR_LEN 2 |
| #define E1000_RAH_POOL_MASK 0x03FC0000 |
| #define E1000_RAH_POOL_1 0x00040000 |
| |
| /* Error Codes */ |
| #define E1000_SUCCESS 0 |
| #define E1000_ERR_NVM 1 |
| #define E1000_ERR_PHY 2 |
| #define E1000_ERR_CONFIG 3 |
| #define E1000_ERR_PARAM 4 |
| #define E1000_ERR_MAC_INIT 5 |
| #define E1000_ERR_PHY_TYPE 6 |
| #define E1000_ERR_RESET 9 |
| #define E1000_ERR_MASTER_REQUESTS_PENDING 10 |
| #define E1000_ERR_HOST_INTERFACE_COMMAND 11 |
| #define E1000_BLK_PHY_RESET 12 |
| #define E1000_ERR_SWFW_SYNC 13 |
| #define E1000_NOT_IMPLEMENTED 14 |
| #define E1000_ERR_MBX 15 |
| |
| /* Loop limit on how long we wait for auto-negotiation to complete */ |
| #define FIBER_LINK_UP_LIMIT 50 |
| #define COPPER_LINK_UP_LIMIT 10 |
| #define PHY_AUTO_NEG_LIMIT 45 |
| #define PHY_FORCE_LIMIT 20 |
| /* Number of 100 microseconds we wait for PCI Express master disable */ |
| #define MASTER_DISABLE_TIMEOUT 800 |
| /* Number of milliseconds we wait for PHY configuration done after MAC reset */ |
| #define PHY_CFG_TIMEOUT 100 |
| /* Number of 2 milliseconds we wait for acquiring MDIO ownership. */ |
| #define MDIO_OWNERSHIP_TIMEOUT 10 |
| /* Number of milliseconds for NVM auto read done after MAC reset. */ |
| #define AUTO_READ_DONE_TIMEOUT 10 |
| |
| /* Flow Control */ |
| #define E1000_FCRTH_RTH 0x0000FFF8 /* Mask Bits[15:3] for RTH */ |
| #define E1000_FCRTH_XFCE 0x80000000 /* External Flow Control Enable */ |
| #define E1000_FCRTL_RTL 0x0000FFF8 /* Mask Bits[15:3] for RTL */ |
| #define E1000_FCRTL_XONE 0x80000000 /* Enable XON frame transmission */ |
| |
| /* Transmit Configuration Word */ |
| #define E1000_TXCW_FD 0x00000020 /* TXCW full duplex */ |
| #define E1000_TXCW_HD 0x00000040 /* TXCW half duplex */ |
| #define E1000_TXCW_PAUSE 0x00000080 /* TXCW sym pause request */ |
| #define E1000_TXCW_ASM_DIR 0x00000100 /* TXCW astm pause direction */ |
| #define E1000_TXCW_PAUSE_MASK 0x00000180 /* TXCW pause request mask */ |
| #define E1000_TXCW_RF 0x00003000 /* TXCW remote fault */ |
| #define E1000_TXCW_NP 0x00008000 /* TXCW next page */ |
| #define E1000_TXCW_CW 0x0000ffff /* TxConfigWord mask */ |
| #define E1000_TXCW_TXC 0x40000000 /* Transmit Config control */ |
| #define E1000_TXCW_ANE 0x80000000 /* Auto-neg enable */ |
| |
| /* Receive Configuration Word */ |
| #define E1000_RXCW_CW 0x0000ffff /* RxConfigWord mask */ |
| #define E1000_RXCW_NC 0x04000000 /* Receive config no carrier */ |
| #define E1000_RXCW_IV 0x08000000 /* Receive config invalid */ |
| #define E1000_RXCW_CC 0x10000000 /* Receive config change */ |
| #define E1000_RXCW_C 0x20000000 /* Receive config */ |
| #define E1000_RXCW_SYNCH 0x40000000 /* Receive config synch */ |
| #define E1000_RXCW_ANC 0x80000000 /* Auto-neg complete */ |
| |
| /* PCI Express Control */ |
| #define E1000_GCR_RXD_NO_SNOOP 0x00000001 |
| #define E1000_GCR_RXDSCW_NO_SNOOP 0x00000002 |
| #define E1000_GCR_RXDSCR_NO_SNOOP 0x00000004 |
| #define E1000_GCR_TXD_NO_SNOOP 0x00000008 |
| #define E1000_GCR_TXDSCW_NO_SNOOP 0x00000010 |
| #define E1000_GCR_TXDSCR_NO_SNOOP 0x00000020 |
| #define E1000_GCR_CMPL_TMOUT_MASK 0x0000F000 |
| #define E1000_GCR_CMPL_TMOUT_10ms 0x00001000 |
| #define E1000_GCR_CMPL_TMOUT_RESEND 0x00010000 |
| #define E1000_GCR_CAP_VER2 0x00040000 |
| |
| #define PCIE_NO_SNOOP_ALL (E1000_GCR_RXD_NO_SNOOP | \ |
| E1000_GCR_RXDSCW_NO_SNOOP | \ |
| E1000_GCR_RXDSCR_NO_SNOOP | \ |
| E1000_GCR_TXD_NO_SNOOP | \ |
| E1000_GCR_TXDSCW_NO_SNOOP | \ |
| E1000_GCR_TXDSCR_NO_SNOOP) |
| |
| /* PHY Control Register */ |
| #define MII_CR_SPEED_SELECT_MSB 0x0040 /* bits 6,13: 10=1000, 01=100, 00=10 */ |
| #define MII_CR_COLL_TEST_ENABLE 0x0080 /* Collision test enable */ |
| #define MII_CR_FULL_DUPLEX 0x0100 /* FDX =1, half duplex =0 */ |
| #define MII_CR_RESTART_AUTO_NEG 0x0200 /* Restart auto negotiation */ |
| #define MII_CR_ISOLATE 0x0400 /* Isolate PHY from MII */ |
| #define MII_CR_POWER_DOWN 0x0800 /* Power down */ |
| #define MII_CR_AUTO_NEG_EN 0x1000 /* Auto Neg Enable */ |
| #define MII_CR_SPEED_SELECT_LSB 0x2000 /* bits 6,13: 10=1000, 01=100, 00=10 */ |
| #define MII_CR_LOOPBACK 0x4000 /* 0 = normal, 1 = loopback */ |
| #define MII_CR_RESET 0x8000 /* 0 = normal, 1 = PHY reset */ |
| #define MII_CR_SPEED_1000 0x0040 |
| #define MII_CR_SPEED_100 0x2000 |
| #define MII_CR_SPEED_10 0x0000 |
| |
| /* PHY Status Register */ |
| #define MII_SR_EXTENDED_CAPS 0x0001 /* Extended register capabilities */ |
| #define MII_SR_JABBER_DETECT 0x0002 /* Jabber Detected */ |
| #define MII_SR_LINK_STATUS 0x0004 /* Link Status 1 = link */ |
| #define MII_SR_AUTONEG_CAPS 0x0008 /* Auto Neg Capable */ |
| #define MII_SR_REMOTE_FAULT 0x0010 /* Remote Fault Detect */ |
| #define MII_SR_AUTONEG_COMPLETE 0x0020 /* Auto Neg Complete */ |
| #define MII_SR_PREAMBLE_SUPPRESS 0x0040 /* Preamble may be suppressed */ |
| #define MII_SR_EXTENDED_STATUS 0x0100 /* Ext. status info in Reg 0x0F */ |
| #define MII_SR_100T2_HD_CAPS 0x0200 /* 100T2 Half Duplex Capable */ |
| #define MII_SR_100T2_FD_CAPS 0x0400 /* 100T2 Full Duplex Capable */ |
| #define MII_SR_10T_HD_CAPS 0x0800 /* 10T Half Duplex Capable */ |
| #define MII_SR_10T_FD_CAPS 0x1000 /* 10T Full Duplex Capable */ |
| #define MII_SR_100X_HD_CAPS 0x2000 /* 100X Half Duplex Capable */ |
| #define MII_SR_100X_FD_CAPS 0x4000 /* 100X Full Duplex Capable */ |
| #define MII_SR_100T4_CAPS 0x8000 /* 100T4 Capable */ |
| |
| /* Autoneg Advertisement Register */ |
| #define NWAY_AR_SELECTOR_FIELD 0x0001 /* indicates IEEE 802.3 CSMA/CD */ |
| #define NWAY_AR_10T_HD_CAPS 0x0020 /* 10T Half Duplex Capable */ |
| #define NWAY_AR_10T_FD_CAPS 0x0040 /* 10T Full Duplex Capable */ |
| #define NWAY_AR_100TX_HD_CAPS 0x0080 /* 100TX Half Duplex Capable */ |
| #define NWAY_AR_100TX_FD_CAPS 0x0100 /* 100TX Full Duplex Capable */ |
| #define NWAY_AR_100T4_CAPS 0x0200 /* 100T4 Capable */ |
| #define NWAY_AR_PAUSE 0x0400 /* Pause operation desired */ |
| #define NWAY_AR_ASM_DIR 0x0800 /* Asymmetric Pause Direction bit */ |
| #define NWAY_AR_REMOTE_FAULT 0x2000 /* Remote Fault detected */ |
| #define NWAY_AR_NEXT_PAGE 0x8000 /* Next Page ability supported */ |
| |
| /* Link Partner Ability Register (Base Page) */ |
| #define NWAY_LPAR_SELECTOR_FIELD 0x0000 /* LP protocol selector field */ |
| #define NWAY_LPAR_10T_HD_CAPS 0x0020 /* LP is 10T Half Duplex Capable */ |
| #define NWAY_LPAR_10T_FD_CAPS 0x0040 /* LP is 10T Full Duplex Capable */ |
| #define NWAY_LPAR_100TX_HD_CAPS 0x0080 /* LP is 100TX Half Duplex Capable */ |
| #define NWAY_LPAR_100TX_FD_CAPS 0x0100 /* LP is 100TX Full Duplex Capable */ |
| #define NWAY_LPAR_100T4_CAPS 0x0200 /* LP is 100T4 Capable */ |
| #define NWAY_LPAR_PAUSE 0x0400 /* LP Pause operation desired */ |
| #define NWAY_LPAR_ASM_DIR 0x0800 /* LP Asymmetric Pause Direction bit */ |
| #define NWAY_LPAR_REMOTE_FAULT 0x2000 /* LP has detected Remote Fault */ |
| #define NWAY_LPAR_ACKNOWLEDGE 0x4000 /* LP has rx'd link code word */ |
| #define NWAY_LPAR_NEXT_PAGE 0x8000 /* Next Page ability supported */ |
| |
| /* Autoneg Expansion Register */ |
| #define NWAY_ER_LP_NWAY_CAPS 0x0001 /* LP has Auto Neg Capability */ |
| #define NWAY_ER_PAGE_RXD 0x0002 /* LP is 10T Half Duplex Capable */ |
| #define NWAY_ER_NEXT_PAGE_CAPS 0x0004 /* LP is 10T Full Duplex Capable */ |
| #define NWAY_ER_LP_NEXT_PAGE_CAPS 0x0008 /* LP is 100TX Half Duplex Capable */ |
| #define NWAY_ER_PAR_DETECT_FAULT 0x0010 /* LP is 100TX Full Duplex Capable */ |
| |
| /* 1000BASE-T Control Register */ |
| #define CR_1000T_ASYM_PAUSE 0x0080 /* Advertise asymmetric pause bit */ |
| #define CR_1000T_HD_CAPS 0x0100 /* Advertise 1000T HD capability */ |
| #define CR_1000T_FD_CAPS 0x0200 /* Advertise 1000T FD capability */ |
| #define CR_1000T_REPEATER_DTE 0x0400 /* 1=Repeater/switch device port */ |
| /* 0=DTE device */ |
| #define CR_1000T_MS_VALUE 0x0800 /* 1=Configure PHY as Master */ |
| /* 0=Configure PHY as Slave */ |
| #define CR_1000T_MS_ENABLE 0x1000 /* 1=Master/Slave manual config value */ |
| /* 0=Automatic Master/Slave config */ |
| #define CR_1000T_TEST_MODE_NORMAL 0x0000 /* Normal Operation */ |
| #define CR_1000T_TEST_MODE_1 0x2000 /* Transmit Waveform test */ |
| #define CR_1000T_TEST_MODE_2 0x4000 /* Master Transmit Jitter test */ |
| #define CR_1000T_TEST_MODE_3 0x6000 /* Slave Transmit Jitter test */ |
| #define CR_1000T_TEST_MODE_4 0x8000 /* Transmitter Distortion test */ |
| |
| /* 1000BASE-T Status Register */ |
| #define SR_1000T_IDLE_ERROR_CNT 0x00FF /* Num idle errors since last read */ |
| #define SR_1000T_ASYM_PAUSE_DIR 0x0100 /* LP asymmetric pause direction bit */ |
| #define SR_1000T_LP_HD_CAPS 0x0400 /* LP is 1000T HD capable */ |
| #define SR_1000T_LP_FD_CAPS 0x0800 /* LP is 1000T FD capable */ |
| #define SR_1000T_REMOTE_RX_STATUS 0x1000 /* Remote receiver OK */ |
| #define SR_1000T_LOCAL_RX_STATUS 0x2000 /* Local receiver OK */ |
| #define SR_1000T_MS_CONFIG_RES 0x4000 /* 1=Local Tx is Master, 0=Slave */ |
| #define SR_1000T_MS_CONFIG_FAULT 0x8000 /* Master/Slave config fault */ |
| |
| #define SR_1000T_PHY_EXCESSIVE_IDLE_ERR_COUNT 5 |
| |
| /* PHY 1000 MII Register/Bit Definitions */ |
| /* PHY Registers defined by IEEE */ |
| #define PHY_CONTROL 0x00 /* Control Register */ |
| #define PHY_STATUS 0x01 /* Status Register */ |
| #define PHY_ID1 0x02 /* Phy Id Reg (word 1) */ |
| #define PHY_ID2 0x03 /* Phy Id Reg (word 2) */ |
| #define PHY_AUTONEG_ADV 0x04 /* Autoneg Advertisement */ |
| #define PHY_LP_ABILITY 0x05 /* Link Partner Ability (Base Page) */ |
| #define PHY_AUTONEG_EXP 0x06 /* Autoneg Expansion Reg */ |
| #define PHY_NEXT_PAGE_TX 0x07 /* Next Page Tx */ |
| #define PHY_LP_NEXT_PAGE 0x08 /* Link Partner Next Page */ |
| #define PHY_1000T_CTRL 0x09 /* 1000Base-T Control Reg */ |
| #define PHY_1000T_STATUS 0x0A /* 1000Base-T Status Reg */ |
| #define PHY_EXT_STATUS 0x0F /* Extended Status Reg */ |
| |
| #define PHY_CONTROL_LB 0x4000 /* PHY Loopback bit */ |
| |
| /* NVM Control */ |
| #define E1000_EECD_SK 0x00000001 /* NVM Clock */ |
| #define E1000_EECD_CS 0x00000002 /* NVM Chip Select */ |
| #define E1000_EECD_DI 0x00000004 /* NVM Data In */ |
| #define E1000_EECD_DO 0x00000008 /* NVM Data Out */ |
| #define E1000_EECD_FWE_MASK 0x00000030 |
| #define E1000_EECD_FWE_DIS 0x00000010 /* Disable FLASH writes */ |
| #define E1000_EECD_FWE_EN 0x00000020 /* Enable FLASH writes */ |
| #define E1000_EECD_FWE_SHIFT 4 |
| #define E1000_EECD_REQ 0x00000040 /* NVM Access Request */ |
| #define E1000_EECD_GNT 0x00000080 /* NVM Access Grant */ |
| #define E1000_EECD_PRES 0x00000100 /* NVM Present */ |
| #define E1000_EECD_SIZE 0x00000200 /* NVM Size (0=64 word 1=256 word) */ |
| /* NVM Addressing bits based on type 0=small, 1=large */ |
| #define E1000_EECD_ADDR_BITS 0x00000400 |
| #define E1000_EECD_TYPE 0x00002000 /* NVM Type (1-SPI, 0-Microwire) */ |
| #define E1000_NVM_GRANT_ATTEMPTS 1000 /* NVM # attempts to gain grant */ |
| #define E1000_EECD_AUTO_RD 0x00000200 /* NVM Auto Read done */ |
| #define E1000_EECD_SIZE_EX_MASK 0x00007800 /* NVM Size */ |
| #define E1000_EECD_SIZE_EX_SHIFT 11 |
| #define E1000_EECD_NVADDS 0x00018000 /* NVM Address Size */ |
| #define E1000_EECD_SELSHAD 0x00020000 /* Select Shadow RAM */ |
| #define E1000_EECD_INITSRAM 0x00040000 /* Initialize Shadow RAM */ |
| #define E1000_EECD_FLUPD 0x00080000 /* Update FLASH */ |
| #define E1000_EECD_AUPDEN 0x00100000 /* Enable Autonomous FLASH update */ |
| #define E1000_EECD_SHADV 0x00200000 /* Shadow RAM Data Valid */ |
| #define E1000_EECD_SEC1VAL 0x00400000 /* Sector One Valid */ |
| #define E1000_EECD_SECVAL_SHIFT 22 |
| #define E1000_EECD_SEC1VAL_VALID_MASK (E1000_EECD_AUTO_RD | E1000_EECD_PRES) |
| |
| #define E1000_NVM_SWDPIN0 0x0001 /* SWDPIN 0 NVM Value */ |
| #define E1000_NVM_LED_LOGIC 0x0020 /* Led Logic Word */ |
| #define E1000_NVM_RW_REG_DATA 16 /* Offset to data in NVM read/write regs */ |
| #define E1000_NVM_RW_REG_DONE 2 /* Offset to READ/WRITE done bit */ |
| #define E1000_NVM_RW_REG_START 1 /* Start operation */ |
| #define E1000_NVM_RW_ADDR_SHIFT 2 /* Shift to the address bits */ |
| #define E1000_NVM_POLL_WRITE 1 /* Flag for polling for write complete */ |
| #define E1000_NVM_POLL_READ 0 /* Flag for polling for read complete */ |
| #define E1000_FLASH_UPDATES 2000 |
| |
| /* NVM Word Offsets */ |
| #define NVM_COMPAT 0x0003 |
| #define NVM_ID_LED_SETTINGS 0x0004 |
| #define NVM_VERSION 0x0005 |
| #define NVM_SERDES_AMPLITUDE 0x0006 /* SERDES output amplitude */ |
| #define NVM_PHY_CLASS_WORD 0x0007 |
| #define NVM_INIT_CONTROL1_REG 0x000A |
| #define NVM_INIT_CONTROL2_REG 0x000F |
| #define NVM_SWDEF_PINS_CTRL_PORT_1 0x0010 |
| #define NVM_INIT_CONTROL3_PORT_B 0x0014 |
| #define NVM_INIT_3GIO_3 0x001A |
| #define NVM_SWDEF_PINS_CTRL_PORT_0 0x0020 |
| #define NVM_INIT_CONTROL3_PORT_A 0x0024 |
| #define NVM_CFG 0x0012 |
| #define NVM_FLASH_VERSION 0x0032 |
| #define NVM_ALT_MAC_ADDR_PTR 0x0037 |
| #define NVM_CHECKSUM_REG 0x003F |
| |
| #define E1000_NVM_CFG_DONE_PORT_0 0x040000 /* MNG config cycle done */ |
| #define E1000_NVM_CFG_DONE_PORT_1 0x080000 /* ...for second port */ |
| |
| /* Mask bits for fields in Word 0x0f of the NVM */ |
| #define NVM_WORD0F_PAUSE_MASK 0x3000 |
| #define NVM_WORD0F_PAUSE 0x1000 |
| #define NVM_WORD0F_ASM_DIR 0x2000 |
| #define NVM_WORD0F_ANE 0x0800 |
| #define NVM_WORD0F_SWPDIO_EXT_MASK 0x00F0 |
| #define NVM_WORD0F_LPLU 0x0001 |
| |
| /* Mask bits for fields in Word 0x1a of the NVM */ |
| #define NVM_WORD1A_ASPM_MASK 0x000C |
| |
| /* For checksumming, the sum of all words in the NVM should equal 0xBABA. */ |
| #define NVM_SUM 0xBABA |
| |
| #define NVM_MAC_ADDR_OFFSET 0 |
| #define NVM_PBA_OFFSET_0 8 |
| #define NVM_PBA_OFFSET_1 9 |
| #define NVM_RESERVED_WORD 0xFFFF |
| #define NVM_PHY_CLASS_A 0x8000 |
| #define NVM_SERDES_AMPLITUDE_MASK 0x000F |
| #define NVM_SIZE_MASK 0x1C00 |
| #define NVM_SIZE_SHIFT 10 |
| #define NVM_WORD_SIZE_BASE_SHIFT 6 |
| #define NVM_SWDPIO_EXT_SHIFT 4 |
| |
| /* NVM Commands - Microwire */ |
| #define NVM_READ_OPCODE_MICROWIRE 0x6 /* NVM read opcode */ |
| #define NVM_WRITE_OPCODE_MICROWIRE 0x5 /* NVM write opcode */ |
| #define NVM_ERASE_OPCODE_MICROWIRE 0x7 /* NVM erase opcode */ |
| #define NVM_EWEN_OPCODE_MICROWIRE 0x13 /* NVM erase/write enable */ |
| #define NVM_EWDS_OPCODE_MICROWIRE 0x10 /* NVM erase/write disable */ |
| |
| /* NVM Commands - SPI */ |
| #define NVM_MAX_RETRY_SPI 5000 /* Max wait of 5ms, for RDY signal */ |
| #define NVM_READ_OPCODE_SPI 0x03 /* NVM read opcode */ |
| #define NVM_WRITE_OPCODE_SPI 0x02 /* NVM write opcode */ |
| #define NVM_A8_OPCODE_SPI 0x08 /* opcode bit-3 = address bit-8 */ |
| #define NVM_WREN_OPCODE_SPI 0x06 /* NVM set Write Enable latch */ |
| #define NVM_WRDI_OPCODE_SPI 0x04 /* NVM reset Write Enable latch */ |
| #define NVM_RDSR_OPCODE_SPI 0x05 /* NVM read Status register */ |
| #define NVM_WRSR_OPCODE_SPI 0x01 /* NVM write Status register */ |
| |
| /* SPI NVM Status Register */ |
| #define NVM_STATUS_RDY_SPI 0x01 |
| #define NVM_STATUS_WEN_SPI 0x02 |
| #define NVM_STATUS_BP0_SPI 0x04 |
| #define NVM_STATUS_BP1_SPI 0x08 |
| #define NVM_STATUS_WPEN_SPI 0x80 |
| |
| /* Word definitions for ID LED Settings */ |
| #define ID_LED_RESERVED_0000 0x0000 |
| #define ID_LED_RESERVED_FFFF 0xFFFF |
| #define ID_LED_DEFAULT ((ID_LED_OFF1_ON2 << 12) | \ |
| (ID_LED_OFF1_OFF2 << 8) | \ |
| (ID_LED_DEF1_DEF2 << 4) | \ |
| (ID_LED_DEF1_DEF2)) |
| #define ID_LED_DEF1_DEF2 0x1 |
| #define ID_LED_DEF1_ON2 0x2 |
| #define ID_LED_DEF1_OFF2 0x3 |
| #define ID_LED_ON1_DEF2 0x4 |
| #define ID_LED_ON1_ON2 0x5 |
| #define ID_LED_ON1_OFF2 0x6 |
| #define ID_LED_OFF1_DEF2 0x7 |
| #define ID_LED_OFF1_ON2 0x8 |
| #define ID_LED_OFF1_OFF2 0x9 |
| |
| #define IGP_ACTIVITY_LED_MASK 0xFFFFF0FF |
| #define IGP_ACTIVITY_LED_ENABLE 0x0300 |
| #define IGP_LED3_MODE 0x07000000 |
| |
| /* PCI/PCI-X/PCI-EX Config space */ |
| #define PCIX_COMMAND_REGISTER 0xE6 |
| #define PCIX_STATUS_REGISTER_LO 0xE8 |
| #define PCIX_STATUS_REGISTER_HI 0xEA |
| #define PCI_HEADER_TYPE_REGISTER 0x0E |
| #define PCIE_LINK_STATUS 0x12 |
| #define PCIE_DEVICE_CONTROL2 0x28 |
| |
| #define PCIX_COMMAND_MMRBC_MASK 0x000C |
| #define PCIX_COMMAND_MMRBC_SHIFT 0x2 |
| #define PCIX_STATUS_HI_MMRBC_MASK 0x0060 |
| #define PCIX_STATUS_HI_MMRBC_SHIFT 0x5 |
| #define PCIX_STATUS_HI_MMRBC_4K 0x3 |
| #define PCIX_STATUS_HI_MMRBC_2K 0x2 |
| #define PCIX_STATUS_LO_FUNC_MASK 0x7 |
| #define PCI_HEADER_TYPE_MULTIFUNC 0x80 |
| #define PCIE_LINK_WIDTH_MASK 0x3F0 |
| #define PCIE_LINK_WIDTH_SHIFT 4 |
| #define PCIE_DEVICE_CONTROL2_16ms 0x0005 |
| |
| #ifndef ETH_ADDR_LEN |
| #define ETH_ADDR_LEN 6 |
| #endif |
| |
| #define PHY_REVISION_MASK 0xFFFFFFF0 |
| #define MAX_PHY_REG_ADDRESS 0x1F /* 5 bit address bus (0-0x1F) */ |
| #define MAX_PHY_MULTI_PAGE_REG 0xF |
| |
| /* Bit definitions for valid PHY IDs. */ |
| /* |
| * I = Integrated |
| * E = External |
| */ |
| #define M88E1000_E_PHY_ID 0x01410C50 |
| #define M88E1000_I_PHY_ID 0x01410C30 |
| #define M88E1011_I_PHY_ID 0x01410C20 |
| #define IGP01E1000_I_PHY_ID 0x02A80380 |
| #define M88E1011_I_REV_4 0x04 |
| #define M88E1111_I_PHY_ID 0x01410CC0 |
| #define GG82563_E_PHY_ID 0x01410CA0 |
| #define IGP03E1000_E_PHY_ID 0x02A80390 |
| #define IFE_E_PHY_ID 0x02A80330 |
| #define IFE_PLUS_E_PHY_ID 0x02A80320 |
| #define IFE_C_E_PHY_ID 0x02A80310 |
| #define M88_VENDOR 0x0141 |
| |
| /* M88E1000 Specific Registers */ |
| #define M88E1000_PHY_SPEC_CTRL 0x10 /* PHY Specific Control Register */ |
| #define M88E1000_PHY_SPEC_STATUS 0x11 /* PHY Specific Status Register */ |
| #define M88E1000_INT_ENABLE 0x12 /* Interrupt Enable Register */ |
| #define M88E1000_INT_STATUS 0x13 /* Interrupt Status Register */ |
| #define M88E1000_EXT_PHY_SPEC_CTRL 0x14 /* Extended PHY Specific Control */ |
| #define M88E1000_RX_ERR_CNTR 0x15 /* Receive Error Counter */ |
| |
| #define M88E1000_PHY_EXT_CTRL 0x1A /* PHY extend control register */ |
| #define M88E1000_PHY_PAGE_SELECT 0x1D /* Reg 29 for page number setting */ |
| #define M88E1000_PHY_GEN_CONTROL 0x1E /* Its meaning depends on reg 29 */ |
| #define M88E1000_PHY_VCO_REG_BIT8 0x100 /* Bits 8 & 11 are adjusted for */ |
| #define M88E1000_PHY_VCO_REG_BIT11 0x800 /* improved BER performance */ |
| |
| /* M88E1000 PHY Specific Control Register */ |
| #define M88E1000_PSCR_JABBER_DISABLE 0x0001 /* 1=Jabber Function disabled */ |
| #define M88E1000_PSCR_POLARITY_REVERSAL 0x0002 /* 1=Polarity Reverse enabled */ |
| #define M88E1000_PSCR_SQE_TEST 0x0004 /* 1=SQE Test enabled */ |
| /* 1=CLK125 low, 0=CLK125 toggling */ |
| #define M88E1000_PSCR_CLK125_DISABLE 0x0010 |
| #define M88E1000_PSCR_MDI_MANUAL_MODE 0x0000 /* MDI Crossover Mode bits 6:5 */ |
| /* Manual MDI configuration */ |
| #define M88E1000_PSCR_MDIX_MANUAL_MODE 0x0020 /* Manual MDIX configuration */ |
| /* 1000BASE-T: Auto crossover, 100BASE-TX/10BASE-T: MDI Mode */ |
| #define M88E1000_PSCR_AUTO_X_1000T 0x0040 |
| /* Auto crossover enabled all speeds */ |
| #define M88E1000_PSCR_AUTO_X_MODE 0x0060 |
| /* |
| * 1=Enable Extended 10BASE-T distance (Lower 10BASE-T Rx Threshold |
| * 0=Normal 10BASE-T Rx Threshold |
| */ |
| #define M88E1000_PSCR_EN_10BT_EXT_DIST 0x0080 |
| /* 1=5-bit interface in 100BASE-TX, 0=MII interface in 100BASE-TX */ |
| #define M88E1000_PSCR_MII_5BIT_ENABLE 0x0100 |
| #define M88E1000_PSCR_SCRAMBLER_DISABLE 0x0200 /* 1=Scrambler disable */ |
| #define M88E1000_PSCR_FORCE_LINK_GOOD 0x0400 /* 1=Force link good */ |
| #define M88E1000_PSCR_ASSERT_CRS_ON_TX 0x0800 /* 1=Assert CRS on Tx */ |
| |
| /* M88E1000 PHY Specific Status Register */ |
| #define M88E1000_PSSR_JABBER 0x0001 /* 1=Jabber */ |
| #define M88E1000_PSSR_REV_POLARITY 0x0002 /* 1=Polarity reversed */ |
| #define M88E1000_PSSR_DOWNSHIFT 0x0020 /* 1=Downshifted */ |
| #define M88E1000_PSSR_MDIX 0x0040 /* 1=MDIX; 0=MDI */ |
| /* |
| * 0 = <50M |
| * 1 = 50-80M |
| * 2 = 80-110M |
| * 3 = 110-140M |
| * 4 = >140M |
| */ |
| #define M88E1000_PSSR_CABLE_LENGTH 0x0380 |
| #define M88E1000_PSSR_LINK 0x0400 /* 1=Link up, 0=Link down */ |
| #define M88E1000_PSSR_SPD_DPLX_RESOLVED 0x0800 /* 1=Speed & Duplex resolved */ |
| #define M88E1000_PSSR_PAGE_RCVD 0x1000 /* 1=Page received */ |
| #define M88E1000_PSSR_DPLX 0x2000 /* 1=Duplex 0=Half Duplex */ |
| #define M88E1000_PSSR_SPEED 0xC000 /* Speed, bits 14:15 */ |
| #define M88E1000_PSSR_10MBS 0x0000 /* 00=10Mbs */ |
| #define M88E1000_PSSR_100MBS 0x4000 /* 01=100Mbs */ |
| #define M88E1000_PSSR_1000MBS 0x8000 /* 10=1000Mbs */ |
| |
| #define M88E1000_PSSR_CABLE_LENGTH_SHIFT 7 |
| |
| /* M88E1000 Extended PHY Specific Control Register */ |
| #define M88E1000_EPSCR_FIBER_LOOPBACK 0x4000 /* 1=Fiber loopback */ |
| /* |
| * 1 = Lost lock detect enabled. |
| * Will assert lost lock and bring |
| * link down if idle not seen |
| * within 1ms in 1000BASE-T |
| */ |
| #define M88E1000_EPSCR_DOWN_NO_IDLE 0x8000 |
| /* |
| * Number of times we will attempt to autonegotiate before downshifting if we |
| * are the master |
| */ |
| #define M88E1000_EPSCR_MASTER_DOWNSHIFT_MASK 0x0C00 |
| #define M88E1000_EPSCR_MASTER_DOWNSHIFT_1X 0x0000 |
| #define M88E1000_EPSCR_MASTER_DOWNSHIFT_2X 0x0400 |
| #define M88E1000_EPSCR_MASTER_DOWNSHIFT_3X 0x0800 |
| #define M88E1000_EPSCR_MASTER_DOWNSHIFT_4X 0x0C00 |
| /* |
| * Number of times we will attempt to autonegotiate before downshifting if we |
| * are the slave |
| */ |
| #define M88E1000_EPSCR_SLAVE_DOWNSHIFT_MASK 0x0300 |
| #define M88E1000_EPSCR_SLAVE_DOWNSHIFT_DIS 0x0000 |
| #define M88E1000_EPSCR_SLAVE_DOWNSHIFT_1X 0x0100 |
| #define M88E1000_EPSCR_SLAVE_DOWNSHIFT_2X 0x0200 |
| #define M88E1000_EPSCR_SLAVE_DOWNSHIFT_3X 0x0300 |
| #define M88E1000_EPSCR_TX_CLK_2_5 0x0060 /* 2.5 MHz TX_CLK */ |
| #define M88E1000_EPSCR_TX_CLK_25 0x0070 /* 25 MHz TX_CLK */ |
| #define M88E1000_EPSCR_TX_CLK_0 0x0000 /* NO TX_CLK */ |
| |
| /* M88EC018 Rev 2 specific DownShift settings */ |
| #define M88EC018_EPSCR_DOWNSHIFT_COUNTER_MASK 0x0E00 |
| #define M88EC018_EPSCR_DOWNSHIFT_COUNTER_1X 0x0000 |
| #define M88EC018_EPSCR_DOWNSHIFT_COUNTER_2X 0x0200 |
| #define M88EC018_EPSCR_DOWNSHIFT_COUNTER_3X 0x0400 |
| #define M88EC018_EPSCR_DOWNSHIFT_COUNTER_4X 0x0600 |
| #define M88EC018_EPSCR_DOWNSHIFT_COUNTER_5X 0x0800 |
| #define M88EC018_EPSCR_DOWNSHIFT_COUNTER_6X 0x0A00 |
| #define M88EC018_EPSCR_DOWNSHIFT_COUNTER_7X 0x0C00 |
| #define M88EC018_EPSCR_DOWNSHIFT_COUNTER_8X 0x0E00 |
| |
| /* |
| * Bits... |
| * 15-5: page |
| * 4-0: register offset |
| */ |
| #define GG82563_PAGE_SHIFT 5 |
| #define GG82563_REG(page, reg) \ |
| (((page) << GG82563_PAGE_SHIFT) | ((reg) & MAX_PHY_REG_ADDRESS)) |
| #define GG82563_MIN_ALT_REG 30 |
| |
| /* GG82563 Specific Registers */ |
| #define GG82563_PHY_SPEC_CTRL \ |
| GG82563_REG(0, 16) /* PHY Specific Control */ |
| #define GG82563_PHY_SPEC_STATUS \ |
| GG82563_REG(0, 17) /* PHY Specific Status */ |
| #define GG82563_PHY_INT_ENABLE \ |
| GG82563_REG(0, 18) /* Interrupt Enable */ |
| #define GG82563_PHY_SPEC_STATUS_2 \ |
| GG82563_REG(0, 19) /* PHY Specific Status 2 */ |
| #define GG82563_PHY_RX_ERR_CNTR \ |
| GG82563_REG(0, 21) /* Receive Error Counter */ |
| #define GG82563_PHY_PAGE_SELECT \ |
| GG82563_REG(0, 22) /* Page Select */ |
| #define GG82563_PHY_SPEC_CTRL_2 \ |
| GG82563_REG(0, 26) /* PHY Specific Control 2 */ |
| #define GG82563_PHY_PAGE_SELECT_ALT \ |
| GG82563_REG(0, 29) /* Alternate Page Select */ |
| #define GG82563_PHY_TEST_CLK_CTRL \ |
| GG82563_REG(0, 30) /* Test Clock Control (use reg. 29 to select) */ |
| |
| #define GG82563_PHY_MAC_SPEC_CTRL \ |
| GG82563_REG(2, 21) /* MAC Specific Control Register */ |
| #define GG82563_PHY_MAC_SPEC_CTRL_2 \ |
| GG82563_REG(2, 26) /* MAC Specific Control 2 */ |
| |
| #define GG82563_PHY_DSP_DISTANCE \ |
| GG82563_REG(5, 26) /* DSP Distance */ |
| |
| /* Page 193 - Port Control Registers */ |
| #define GG82563_PHY_KMRN_MODE_CTRL \ |
| GG82563_REG(193, 16) /* Kumeran Mode Control */ |
| #define GG82563_PHY_PORT_RESET \ |
| GG82563_REG(193, 17) /* Port Reset */ |
| #define GG82563_PHY_REVISION_ID \ |
| GG82563_REG(193, 18) /* Revision ID */ |
| #define GG82563_PHY_DEVICE_ID \ |
| GG82563_REG(193, 19) /* Device ID */ |
| #define GG82563_PHY_PWR_MGMT_CTRL \ |
| GG82563_REG(193, 20) /* Power Management Control */ |
| #define GG82563_PHY_RATE_ADAPT_CTRL \ |
| GG82563_REG(193, 25) /* Rate Adaptation Control */ |
| |
| /* Page 194 - KMRN Registers */ |
| #define GG82563_PHY_KMRN_FIFO_CTRL_STAT \ |
| GG82563_REG(194, 16) /* FIFO's Control/Status */ |
| #define GG82563_PHY_KMRN_CTRL \ |
| GG82563_REG(194, 17) /* Control */ |
| #define GG82563_PHY_INBAND_CTRL \ |
| GG82563_REG(194, 18) /* Inband Control */ |
| #define GG82563_PHY_KMRN_DIAGNOSTIC \ |
| GG82563_REG(194, 19) /* Diagnostic */ |
| #define GG82563_PHY_ACK_TIMEOUTS \ |
| GG82563_REG(194, 20) /* Acknowledge Timeouts */ |
| #define GG82563_PHY_ADV_ABILITY \ |
| GG82563_REG(194, 21) /* Advertised Ability */ |
| #define GG82563_PHY_LINK_PARTNER_ADV_ABILITY \ |
| GG82563_REG(194, 23) /* Link Partner Advertised Ability */ |
| #define GG82563_PHY_ADV_NEXT_PAGE \ |
| GG82563_REG(194, 24) /* Advertised Next Page */ |
| #define GG82563_PHY_LINK_PARTNER_ADV_NEXT_PAGE \ |
| GG82563_REG(194, 25) /* Link Partner Advertised Next page */ |
| #define GG82563_PHY_KMRN_MISC \ |
| GG82563_REG(194, 26) /* Misc. */ |
| |
| /* MDI Control */ |
| #define E1000_MDIC_DATA_MASK 0x0000FFFF |
| #define E1000_MDIC_REG_MASK 0x001F0000 |
| #define E1000_MDIC_REG_SHIFT 16 |
| #define E1000_MDIC_PHY_MASK 0x03E00000 |
| #define E1000_MDIC_PHY_SHIFT 21 |
| #define E1000_MDIC_OP_WRITE 0x04000000 |
| #define E1000_MDIC_OP_READ 0x08000000 |
| #define E1000_MDIC_READY 0x10000000 |
| #define E1000_MDIC_INT_EN 0x20000000 |
| #define E1000_MDIC_ERROR 0x40000000 |
| |
| /* SerDes Control */ |
| #define E1000_GEN_CTL_READY 0x80000000 |
| #define E1000_GEN_CTL_ADDRESS_SHIFT 8 |
| #define E1000_GEN_POLL_TIMEOUT 640 |
| |
| #endif /* _E1000_DEFINES_H_ */ |
